strengthened filament guide for iroberti s um2 feeder 3d models

Install the Ultimaker 2 feeder on your existing Ultimaker 1 machine. ...Consider pairing it with Robert's UM2 Alternative Feeder, a design available at Youmagine: https://www.youmagine.com/designs/alternative-um2-feeder-version-two

This thing is a Filament guide for Scalar S 3D printers, also suitable for any printer using 2020 extrusions profiles. Thanks to Alain B for creating this design! Updates: * September 25, 2017: the original release was made available. To open...

... about its stability. The roller design from Thingiverse's 3342775 has been incorporated into this new design. Both originators of these designs deserve recognition for their outstanding work and creative contributions to the world of 3D printing.

I wanted: bigger distance to the extruder, even on taller prints. less risk of derailing and rat nest on the filament spool, due to slack in the filament caused by extruder movements. Happy printing! Print instructionsI have successfully printed...

For those of you who removed the annoyingly unreliable filament-out sensor on your Anycubic i3 Mega or Mega S. Use this filament guide in place of the sensor assembly. ...You will need to cut a piece of plastic tubing (I used the PET tubing from a pen...

This is simply a replacement clip for Filboyd's Filament Guide. The original clip kept breaking and coming off. This clip has a hole for the screw in the printer's frame so it will not come out. ... The peg with the hole goes on the bottom, of course.

for dual head. ...avoid wet atmosphere, put silica gel inside.https://github.com/atsukita1969/filament-spool-feeder

I've successfully built an enclosure for my CR10-S, but encountered a problem with underextrusion due to excessive friction. The filament is currently supported by a stand on top of the enclosure, causing it to enter straight down through the roof...

The filament guide integrated in its design was an appealing feature; however, I found that leaving it open allowed the filament to gradually escape from the guide. ...To prevent this, I employed FreeCAD and modified it by transforming the end into a...

It's meant to be fitted between the tensioning bolts on a Wade's extruder, accounting for 5mm springs over the bolts as well.\nThis will ensure the filament stays on track and makes loading a bit easier too. ... Note: This requires a drill out using a...

This ingenious adapter plate makes it a breeze to attach your Ultimaker 2 plus feeder to an original UM2+ machine. Simply position the adapter between the plastic and metal components of the feeder, and you're ready to roll! With this clever setup,...

I'm updating this original filament guide to ensure safe printing with 3mm reinforced filaments and a strengthened filament holder. Standard guides may snap if the spool is close to the x carriage due to left-to-right motion. To avoid this, I've...

To resolve issues with broken filament pieces, I upgraded the design of my spool holders by positioning them on top using cover holes and printed guides. This improvement not only prevents print failure but also makes changing colors effortless! The...

for dual head. ...avoid wet atmosphere, put silica gel inside.

To avoid jamming, I devised a filament feeder for my extruder. Secured with a tie-wrap via an unused bolt slot, it ensures smooth guidance when printing. In version 2, I improved the design with a genuine guidance cylinder to prevent filament pulling...

Material Handling for the Ultimaker 2+ Simply replace a screw from the enclosure (highlighted green in the picture) with an M3 x 15 mm screw and tighten securely. ... Here is the same material handling, rotating with ball bearings: link still to come.

... To get started, obtain all parts for the feeder from your local distributor. Your feeder motor must have a D-shaped axis in order to reuse it. Next, procure the feeder components from your nearby reseller. Print the bracket, then mount the feeder.

This piece is intended to accept the UM2+ feeder. Remove the motor from the board by disconnecting it and then reattach once mounted outside. ...Two M3 screws are required to attach this piece to the back panel where the motor was located.

As a gearbox, it moves the knurled bolt a few centimeters outwards and upwards, and provides a new nema17 hole pattern that enables compatibility with any feeder designed for the standard feeder position on the UM2, including the IRobertI feeder and...

... If someone wants to use this, they'll need to tinker with the firmware to reverse the feeder's direction - or simply mirror the print of the body part itself, which could be a more straightforward option if you're not up for customizing the code.

I designed a custom-length core for the spoolholder from iRoberti, found at https://www.youmagine.com/designs/low-friction-um2-spoolholder. This version incorporates 608 bearings and includes a precise-fit spacer that can be scaled as needed. ...The...

It helps to smoothly guide filament to the feeder and works well with all materials (PLA, ABS, PETG, TPU...). There are 3 different wheels to choose from - you only need 1 for the mod to work. ... I'd recommend printing all with 20% in-fill except for...

I used anubis86's "Soft Bowden Filament Guide without Cable Holder" as my template... then I thought to myself... "I want that cable securely in place!!!" So, I modified it... and I uploaded both versions... so you can print them too... ... This one...

for anyone who wants to load their non dremel filament from the top. ... here's a simple filament guide to get the job done every time. ... Parts needed 2 bearings 1 m3 25mm bolt 1 m2 nut

This is a big-wheel filament feeder to guide the filament in cleanly. Parts required: one M6x30 bolt or a printed axle one 17x6x6 bearing This part is retained under the filament switch itself and clamped by the original 4 screws. There is a...

... requiring disassembly of the entire printhead. I use this top part with a modified feeder designed by IRobertI, specifically the 1.75mm version available on Youmagine at https://www.youmagine.com/designs/alternative-feeder-1-75mm-version

... tube length. ...Additionally, the spool's inspection and accessibility have been significantly enhanced for improved usability. ...Furthermore, the print head's XY displacement speed has been increased for faster and more precise printing capabilities.

... caused by underextrusion), it will only break inside the nut, not the intended housing. I successfully used this guide on both the incoming and outgoing sides of my MK8 extruder and found it works flawlessly for keeping filament nicely guided.

I was determined to mount my filament spool on top of the CR-10s but many feeders I found restricted Z axis height, or failed to integrate the filament run out sensor. This design addresses both issues effectively. It required a significant amount...

... without altering original components, providing stability to the feeder tube during printing. Download STL and STEP files for printing, then clip over the existing filament guide, thread the filament through the new guide and into the printer head.