sylvester cat 3d models

... all STEP files are added for whoever wants to remix/adjust to there liking. Since I always tend to get frustrated by only having STL files of models that I want to improve/adjust I want to save you the pain of this and enable you to be creative :-).

To connect this to the second hand holder disc, I bought a plastic tube of 1mm inner diameter from a modeling shop. I pinched one side a bit to make it flatter. This seems to work, but maybe I will have to glue it on the pin. I didn't do so yet...

The automatic transmission in some models has a tendency to fail prematurely. This usually happens around an average mileage of 108,000. **1.1 Identifying Transmission Issues** Transmission failure can be determined through comprehensive...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

The straps used to complete the clamp are downloadable from the original model's site https://www.prusaprinters.org/prints/122320-one-for-all-cable-strap-print-in-place-clamp How to create your clamp & accessoriesSelect the clamp size...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

Printing Recommended slicer settings: Resolution: 0.1mm - 0.2mm Infill: 10% - 20% Supports: Doesn't Matter Rafts: Doesn't Matter License The "Customizable Arduino Nano LED Candle (2 - 6 LEDs)" model (.stl) is licensed under the CC BY license by Code...

You can find a somewhat more detailed list of supplies in my Instructable at https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Basically any combination will do (as long as the driver is 3.3" or smaller so it fits the...

A custom-made enclosure specifically designed for the Raspberry Pi computer assistant Assistant assistant A bespoke casing tailored to fit the Raspberry Pi device. assistant Created especially for the Raspberry Pi, this is a one-of-a-kind case. ...

I was basically trying to address two "issues" of my Anycubic Vyper: - The PSU and Mainboard 24V fans are very loud - I want to upgrade my Vyper with an OctoPrint/OctoPi setup So here is my result: - An upgraded PSU cover featuring a 92mm fan mount...

...Please check if they are valid for your model.Choice & file prefixesABCDcap typeFXFXSFXEplainAAAbelt tensionBBBtyre inflationCDDall cap variants use the same gasketgasketGGGFitI have printed two dozens of variants during development of the caps.

Cable clamps bolt to the Extruder mount bolts to keep the cabling tidy, which I've not used yet as I can currently only run 1 of the heaters at present (my A20M control board is a V4.1 model which doesnt have the components fitted to allow for dual...

You may need to adjust your printer, sand the chamber a little, or apply some force, as the parts were modeled to fit with ZERO clearance, to assure the best possible bond when using superglue. Just apply superglue to the syringe holder anywhere...

4028 fan mount: Note this is modelled with internal supports in the top section of the duct to make it easier to print. Please remove these supports after printing. 4 x M3 32 mm (upper fan mount) 2 x M3 x 12 mm cap screws (lower fan mount) 6 x M3...

Remember to check the wiring of your relay if you use a different model or brand. Adjustments If you set the microswitch to click when the bed is at Y=220, then it will work out of the box with Cura. I still recommend you to modify you G-code to...

If you have a tuned in printer, bump the speeds up a little for a dramatic improvement, (make sure wall thickness is a multiplier of your nozzle thickness - The parameters are important and there are a lot of dependencies, Make sure you have done the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

The Tunnelplan Wind Turbine is a 1:10 scale model of an existing wind turbine. The diameter of the rotor is 2000 mm (20 meters) and the tower height is 1200 mm (40 meters). the max.ceiling height inside the house. Solution 4 energy...

Downloaded some Radio Control model yacht designs. Non of them suited my fancy for building, so I decided to come up with my own. Main Desing principles... No Keel! -> Surf Board / Windsurfer style. Light Weight (relative to size of jib!) ...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

The COMPLETE Order of the Labyrinth bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The strong Minocs of the Order of the Labyrinth are the descendants of Tesevros the Wise,...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

Just copy your gcode to the same folder as the exe, run it, select the options you want and when you've confirmed your choice it will automatically open the first gcode in the same folder and write the temperature changes for you.Extract...

...Composed of two pieces - a base for the motor and a cover - the protector fits perfectly on your pistol model, keeping your magazine safe and protected throughout the action. Don't let a lost magazine ruin your play - get our magazine protector now!

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

If you want to use the hardware I intended this to use: Hinges Bolts- https://www.mcmaster.com/91292A018/ (you will need to thread inner most hinge) Hinge spacer- https://www.mcmaster.com/91755A311/ (you can see in the photos a little bit of white in...

We also offer other variations of this light if needed to fit your specific application, 120-277V AC, 12-24V DC, and 0-10V dimmable models.Our EPL-24-2L-LED-480V LED light fixture is NRTL Listed for United States and Canada approved for use in paint...