syma x8 3d models
2342 3d models found related to syma x8.thingiverse
A simple descent clamp for Syma X8 quadcopter. Installs in place of the camera, controlled the same way - "photo" and "video" buttons for openning and closing the clamp. ... BOM: - <a href...
thingiverse
This is a Syma X8 modified antenna adaptor. ...If you need more information, please write me.
thingiverse
syma x8 gimbal for gopro, sj4000 ....... ...you must generate supports for part gimbal1 I print with PLA, infill 20%
thingiverse
This is a case to the battery of Syma X8SW to use a simple pack of 7.4 v 2000mAh of other models of Syma X8 series (like X8C, X8HW etc) I'm stel work on this, suggestions are welcome. ... BE CAREFUL with the polarity!
thingiverse
The idea is to replace the original Flight Controller's support in the Syma's X8 body, so it becomes possible to use a bigger battery under it. At the same time, this piece provides support for the Power Distribution Board of the Phantom 2, as well,...
thingiverse
So I had a number of these extra Syma X8 motor housings (http://amzn.to/2l50c4k) laying around so I decided to design a 3D printable adapter to use them on a quad build project! You can also get the reciver here (http://amzn.to/2lgVFY3) to drive the...
thingiverse
I have been asked by a number of viewers about brushless motor mounts for the Syma X8 so I went ahead and designed one up. Now I had to do a little give and take in the design to make it somewhat generic for various brushless motors so you might...
thingiverse
A propeller guard for the syma X8C/W/G drone. This is a first version. Suggestions are welcome. Screwholes have to be drilled manualy. ...Print Settings Rafts: No ...
thingiverse
GoPro camera mount for Syma X8 Quadcopterhttp://www.symatoys.com/product/show/1923.html Print Settings Printer: PicasoPro250 Rafts: No Supports: No Resolution: 0.2 Infill: 100% Notes: APS Plastic
thingiverse
For the Syma X8 I made new feet in front, the original ones are in the way while filming with my GoPro Hero 7 Black, now no more :) Print it like shown at the picture
thingiverse
I modified the piece to adapt it to a drone syma x8. So with a lightweight set (25g with battery and camera) and quick assembly can use the x8 for fpv with little weight and highly integrated. ...The battery I've used is from JJRC H31.
thingiverse
İ recently decided to use my left over SYMA X8 shell with some more modern flight controller and other extras only problem was, mounting it to shell, so i quickly made this it has very less details so 3D Printing quite easy, no complex extras also...
thingiverse
YouCute made a brushless motor retrofit for Syma X8 that uses these blade shims to connect. Since the kit is gone & shims are nowhere to be found... 3d printing to the rescue! ... Probably should print with a stronger material (aka not PLA)
thingiverse
It is a very special project that mounts a Phantom 2 into a Syma's X8 body. Why? ...Just because I had it hanging around here at the lab!
thingiverse
Main Syma X8 Parts List: Syma X8 Complete Motor Assembly: http://amzn.to/2mT0lVP Syma X8 Prop Kit: http://amzn.to/2m7Yhtg Syma X8 2000 mah batterys and charger: http://amzn.to/2mGCJHh Syma X8 Hover Board Receiver: http://amzn.to/2m7RfEE Syma X8...
thingiverse
This is a loop hook for a carbiner for use with a syma drone. This was designed by blender which is a free 3d software. ... www.blender.org
thingiverse
The drone involved here it's the Helicute's Zenith (Mirage with GPS), I saw that it's the clone of the Syma X8 but no 100% sure. If someone tries it could share in the comments. (Maybe you need to add support blocker just up the gear, when the...
thingiverse
This is a prop spinner cone for the Syma X8 series quadcopter, or any other 3mm shaft. Photo is shown next to the original (chrome) spinner cone. Update: v2 STLs are modified slightly to allow better clearance for the prop clamping mechanism. ...
thingiverse
Edit it online https://www.tinkercad.com/things/6mZh9VDDO7Z and fits three Syma X8 series batteries for charging or storage. For more information on this build vist us at http://Video-Drone.DIY3DTech.com or our parent site of...
thingiverse
As this transmitter modification allows a lager 2.4 Gig-Hz antenna (see below) to mounted to the back of the Syma X8 series (and possibly the X5 too) transmitter. There are two version, the large is designed for the "larger" 2.4gig mounts...
thingiverse
This thing is a near stock sized blade guard that I designed in Fusion 360. It is a very good fit and is stylized similar to the stock blade guard. I printed it out of PetG and it is considerably stronger than the original guards. It weighs in at 11...
thingiverse
Added gusset supports to https://www.thingiverse.com/mwinzer Custom X8C Leg
thingiverse
pour fixer antenne 2.4 ghz diamètre 6 mm This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/2MJEVLEzjgd
prusaprinters
... mount shattered. ...I drew up another that fits my SYMA X8 nice and snug. Print Settings Printer Brand: Printrbot Printer: Printrbot Simple Metal Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 30% Category: R/C Vehicles
thingiverse
There are a number of you tube videos showing a modification to add an external antenna. I don't need a FPV screen on the controller and didn't want to drill a hole in it, so I created this adapter that takes the place of the dummy antenna on the...