tail lights 3d models

I'm having trouble with my 2017 Yaris, the tail light bulb went out and the socket that holds it was ridiculously tight to turn by hand. My fingers couldn't grasp it because my hands are too large for the space. This clever tool fits over the back of...

https://youtu.be/r0z29SjVY2Q After watching a few generic LED tail lights on Amazon and searching, I decided to get the caliper, pen, paper, and Fusion 360 and make one of my own. After driving, I had to make some revisions. #1 - I was riding around...

It is a Tail-LIGHT after all, and visibility is absolutely critical otherwise it's a dangerous piece of plastic when people can't see your brake-light! 7/25/17 - After more testing, I determined that the original design was way too thick to be safe....

Support my work by clicking on an ad on my website https://bobanl.blogspot.com/2019/10/mibo-tail-light-holder-ii.html or using the PayPal donate button. XANES2 light from BANGGOOD requires two screws with nuts: 5x20. The screw hole is now 10mm in...

The dull red tail light glass is an embarrassment to this otherwise fine toy-grade model RC from Asahi in my opinion. So, I created a 3D model of the glass for printing in clear material, and I used clear Taulman Bridge Nylon in the pictures, but...

Rear light housing for Aliexpress tail lighthttps://de.aliexpress.com/item/32843564666.html?spm=a2g0o.order_detail.order_detail_item.3.f3ff6368Mna47Y&gatewayAdapt=glo2deuFits to 27.2mm SteatpostPrinted in ASA without support Print settings:Infill...

This is a simple holder to attach standard tail (80mm between screws) light to bicycle fender. ... Light screw distance: 80mm Holder angle: 45° Screws nominal: M5

... Print first, place 5mm leds, wire together, test with a 9v, then. figure out your wiring 3. You'll need to open your tails so set aside a day or two without the car. 4. ...Take your time opening them cause they will crack (ask me how I know)

Gum container stick for rear view lights.

Universal Bike Light Holder Compatible with All Saddle Styles

12V Connector for rear light Lada Niva 1700 model. ... You´ll need 6 crimp terminals and wire on each connector.

The Rear Light Seal RCX is a specific type of seal designed to provide maximum protection against water and dust intrusion into the rear lights of vehicles. ...This seal is typically made from a high-quality rubber compound that is resistant to aging,...

I obtained this design from to0w1r3d, but I wasn't pleased with the line separating the American flag and the blinker light area. ...Therefore, I eliminated it.

When the Traxxas Wheelie Bar is mounted on a E-Revo Mini, the original Traxxas Light Kit cannot be mounted anymore as both are using the same mounting spot on the chassis. This print relocates the light kit behind the Wheelie Bar. ...All 4 LEDs are...

I like this light since it can provide 58 hours steady light for the needs of Randonneurs / Audax / other ultra endurance activity ** Strength of this design seems no enough, I designed another one here using original rubber brand:...

Since the RTR has stickers where the lights go, I used a pure acetone-based nail polish remover and some Q-tips to remove the paint behind the sticker, allowing the light to shine through. For the headlights, shipping damage cracked the body in the...

Brake light holder now in stock for electric bicycles, purchase online here. ... https://fr.aliexpress.com/item/33030563867.html?spm=a2g0s.12269583.0.0.12831c61skHoNq The cable simply passes through the hole and emerges from underneath.

Fairly precise model of modern rear bike lamp from Supernova. ...If you need further details, that are missing in the model, let me know! Manufacturer: https://supernova-lights.com/m99-tl-2/

This is a replacement contact plate for the 1157 bulb in the brake/running light socket of a first gen Isuzu trooper. ...I used a Dorman universal socket (85860) for new contacts, and spliced them in to the wire harness.

Custom LED housing to fit an Optronics STL-12RB light, as seen on my youtube channel @squirrelsworkshop youtube.com/squirrelsworkshop Very few supports are needed if printing with the flange surface down.

This is a simple clip that I designed for airsoft games requiring a dead light. ...It fits the Bell Pharos 150 and allows it to slip into molle webbing.

Universal rear light mount for a Topeak TetraRack M2.I didn't like the original cateye mount, and wanted to use my own light, while retaining original hardware. ...So here we are!</p><p>Hardware to assemble: 2x M4x12mm screws, washers, nuts.</p><p>The...

An Additional Rear Light for Safety and Visibility at Night Riding There are 2 Files Front And Rear Bumper You have to but LED standard USB rechargeable to fitted rear Bumper mount. ...Copy this Link to buy the back light --> t.ly/H0VY Recommend print...

It appears that this light has been discontinued: http://www.clasohlson.com/uk/Asaklitt-LED-Rear-Bike-Light/34-7812 Given its discontinuation, I'm even more motivated to fix the old one, as it's no longer possible for me to purchase a replacement of...

The assembly fits both 4" round led brake/turn and 4" led reverse lights available online. The back of the assembly curves to match the body radius on the rv, necessitating mounting decisions by the user. An access panel inside can be created using...

I needed a simple adapter to let me mount bike lights on my recumbent's rack, since I didn't have a standard seatpost. ...A 3/16 inch bolt did the trick - it fit perfectly into the existing hole in my rack.

A clamp to secure a rear bike light to an older type of luggage rack is required. The clamp must fit racks with 8mm bars that are approximately 85mm apart. There may be a few mm of play in either direction, so objects can be stretched or shrunk...

Instead, I opted to use a small bungee cord to accommodate the movement and prevent the light from flipping backwards towards the deck. So far, this solution has worked great! The taillight with turn signals that I attached can be seen here:...

I've made a customization of the holder, which is the middle piece, designed specifically for lights that need to be mounted on a horizontal rod. ...If you're looking for this setup, simply print my model and head over to Kabakneela's original design to...

I purchased these extremely affordable bike lights for my Evolve which notoriously turn themselves off with a simple bump but had modified them to resist shock and now function flawlessly.\r\n\r\nSo, I needed a more reliable way to mount them without...