talentcell battery 3d models
71830 3d models found related to talentcell battery.grabcad
A model for the TalentCell Rechargeable Battery Pack. ...Mass, specifications, and dimensions are as follows: - Mass = 500g - Dimensions = 5.1" x 1" x 3" - Model number: YB1206000-USB - Capacity: 12000mAh - Current: 2A @ 5V, 3A @ 12V (DC)Link:...
thingiverse
Battery holder for the Spark Amp using the NB7101 TalentCell Battery purchased on Amazon. It uses exist screws on the back so it does not require new holes or void the warranty if you need to remove it for warranty care. It also fits in with my...
thingiverse
A Battery Stand for a Talentcell LiPo that I use for AP I wanted to stand the battery upright and stable in the tripod tray. It has a 35mm hole to clear the twist-lock in the center of the tray. I use velcro on all my astro-bits for mounting...
thingiverse
Needed something to hold a battery in place on a project. ...This was the result.
thingiverse
Needed something to hold a battery in place on a project. This was the result. ... Printing:
prusaprinters
This box was designed specifically for a TalentCell Rechargeable 11Ah battery to be held with a velcro strap to the inside of one of the fork arms. ... With a short cable to the telescope, I never have to worry about the wire getting wrapped again.</p>...
grabcad
This is a low-details model of the TalentCell YB1203000-USB battery pack.
thingiverse
At the request of a fellow Spark Amp owner, I redesigned my original battery holder to hold only the Talentcell NB7102 battery. I've uploaded the .stl file, as well as including the Fusion 360 .f3d file and the .step file in case that might be useful...
thingiverse
The model I used is [TalentCell's PB240A1 12V Battery Pack](http://www.talentcell.com/products/24v-battery/pb240a1-rechargeable-22400mah.html). Since this model has LEDs on it I designed the remix to have the ports come out the bottom of the mount so...
thingiverse
Tray to hold a TalentCell Li-Ion Battery Pack (Model:YB1206000-USB) to a Celestron Tripod with 1.5" diameter legs. Print the "test" file for a quick (comparatively) test to make sure it will fit firmly in place on the leg. Scale as necessary, but...
thingiverse
This is a battery case to mount a TalentCell 12V/6000mAh USB battery (affiliate link: https://amzn.to/2ywWvbW ) under an Electric Eel Wheel Nano by Dreaming Robots (Thingiverse: mribble). You can see the battery lights through one of the top slots. ...
thingiverse
This bracket is designed to hold the power board of a Talentcell 6000mAh (https://www.amazon.com/gp/product/B00ME3ZH7C?ie=UTF8&psc=1&linkCode=sl1&tag=thpefi0f-20&linkId=04dc49866cc452a9f995268753a81344&language=en_US&ref_=as_li_ss_tl) on edge so you...
grabcad
The size of the 12V Output/Input port is 5.5 mm x 2.1 mm.Description from...
thingiverse
Designed to hold a TalentCell 11,000 mAh battery (model YB12011000-USB) that I use to power my telescope. The attach point is designed for a 2in leg, but it should hold with anything smaller. The battery just fits. ...The pocket is 40mm x 81mm so any...
grabcad
TalentCell Rechargeable 12V 3000mAh Lithium ion Battery Pack - HolderInside Dimensions:23.5*61*105mm
thingiverse
This will fit Talentcell Battery 3000mah with or without USB. original use proton pack build. ... You can ad a zip tie on the open end for more secure mount.
thingiverse
This is a minimal case design for the lithium cells of the TalentCell 6000mah battery (without USB port) for use in the HasLab Proton Pack. This fits perfectly in the void below the controller and under the stock D-cell battery holder. The intent is...
thingiverse
... for screwdriver access. I use the Talentcell battery to power my ASI Air Plus, which is mounted on the OTA. I sometimes have AZMP GPS failure if the ASIAir is powered when starting the mount up. ... If the ASIAir is off there is never a problem.
thingiverse
Meade ETX #884 field tripod bracket that has a cutout for the Talentcell 3000mah battery and an Autostar holder bracket.
grabcad
Mounting pieces for the TalentCell Rechargeable battery pack. ...The picture shows the mounting pieces in use in a larger Robot set up.
thingiverse
Edit it online https://www.tinkercad.com/things/dSqTgbqaGkp This should work for goth of these battery packs: * [TalentCell Rechargeable 12V 6000mAh/5V 12000mAh Lithium ion Battery...
thingiverse
... to the telescope's moving part so that I wouldn't have to worry about the long cord wrapping around and breaking something. ... I found this Talentcell battery on Amazon that was a good fit and I designed this small box to attach it to the fork arm.
thingiverse
I designed this quick bracket to mount the amazon TalentCell battery to your 15mm twin rod camera rig. ... You can use most any adapter, but I used this one from amazon:...
thingiverse
Here’s the solution I came up with for mounting a de-cased Talentcell YB1206000-USB battery into the Q-pack MK3. I modeled and printed a plate to make use of the void in the bottom Booster Box. It fits very snugly into place and even slots over...
thingiverse
The TalentCell battery has a higher capacity than the Celestron PowerTank, is cheaper, and is far smaller and lighter, making it mountable. Mounting it on the tripod means you don't have it on the ground at your feet to trip over. ... I designed this to...
thingiverse
Bracket to hold 12v Talentcell Rechargeable Battery used to power the DJI FPV Goggles. Bracket holds battery on the strap so you don't have to have the battery in your pocket. ... Link to battery:...
thingiverse
The TalentCell battery has a higher capacity than the Celestron PowerTank, is cheaper, and is far smaller and lighter, making it mountable, so you don't have it at your feet to trip over. I previously mounted it on the tripod, but mounting it on the...
thingiverse
*Version 2.0 Here’s the solution I came up with for mounting a de-cased Talentcell YB1206000-USB battery into the Q-pack MK3. I modeled and printed a plate to make use of the void in the bottom Booster Box. It fits very snugly into place and even...