tape adapter 3d models

Case for ultimateII tape adapter by Gideons 1541 is ideal for gamers on-the-go who require an extra layer of protection for their high-tech device.

This is a locking tape adapter designed specifically for use with the GaffGun. ...It has worked successfully for me, but I must stress that its effectiveness cannot be guaranteed for all users.

I needed to create an adapter in my laboratory to connect two different barrier tape systems from the links...

The design is based on the look of another tape adapter on thingiverse by VIC_Camelot: https://www.thingiverse.com/thing:2412824It's designed from scratch in Fusion 360, and might not be as nice looking as VIC_Camelot's design. However, the...

The design draws inspiration from another tape adapter found on thingiverse by VIC_Camelot: https://www.thingiverse.com/thing:2412824. The design was created from scratch in Fusion 360 and may not be as visually appealing as VIC_Camelot's original...

Simple case for 1541U2 tape adapter. ... BOM: 2 x M3 x 8 mm screws Print Settings Printer: Prusa i3 MK2 Rafts: Not required Supports: None needed Resolution: 0.2 mm layer height Infill: 15-20% density Notes: Print the bottom and top parts of the...

If you spot any issues, such as the unit not fitting snugly in the C64 or the real tape adapter edge connector not seating properly on the protruding circuit board, please share your concerns in the comments below. ... The Ultimate II+ project can be...

An enclosure designed specifically for the 1541 Ultimate II tape adapter, compatible with Commodore 64 and 128 systems. http://www.1541ultimate.net/content/index.php In addition to safeguarding the bare circuit board, this protective casing...

An adapter to allow the use of braodcast 10 inch tapes on reel to reel tape recorders.

Yes, there is indeed a left-handed tape measure available - check it out here: https://amzn.to/2NBvNbh (Note: I don't sell them, but I do use them myself!) If you're involved in any project that requires repeatable layout marking, this tool is...

Because I was already using taped hooks for my picture frames, I decided to use the same Tesa Powerstrips (string, double sided, easily removable tape strips) to glue them to the wall. The two pins are spaced for the baseplate of the SteamVR...

Because I was already using taped hooks for my picture frames, I decided to use the same Tesa Powerstrips (string, double sided, easily removable tape strips) to glue them to the wall. The two pins are spaced for the baseplate of the SteamVR...

Because I was already using taped hooks for my picture frames, I decided to use the same Tesa Powerstrips (string, double sided, easily removable tape strips) to glue them to the wall. The two pins are spaced for the baseplate of the SteamVR...

She reworked the upper section of the casing to create a smooth surface and tweaked the lower portion to perfectly align with the modified top.

Convert your old empty tape dispensers to fit washi tape with this adapter! Designed for standard Scotch tape dispensers. ... Example photo shows 1.5 cm washi tape.

To mount that you will need: - 1x printed adapter plate - 4x brass heated insert (M3, 4mm long, 5mm outer diameter) - https://www.aliexpress.com/item/4000232858343.html?spm=a2g0s.9042311.0.0.27424c4d2x9wzR - 4x M3x10 countersunk screw - double sided...

This will allow you to use heavy-duty mounting-tape to hang up the Honeycomb Storage Wall. The pegs fit inside the honeycomb cells from the back and the inner hole has the same size as the other adapters in the system, allowing you to place...

So, on a spare night when I didn't have to deal with pesky kids or a demanding wife (Just kidding, honey), I measured out my tape adapter and created a free model of my own. Here is the first version of the official Camelot Case for the 1541U II+...

An enclosure for the 1541 Ultimate II tape adapter for the Commodore 64 and 128, based on https://www.thingiverse.com/thing:3551198 This enclosure is for an older, wider board version. You will need to drill two holes into the board in order to...

This is my proposition of housing of the tape adapter of Ultimate II+ cartridge for Commodore 64. In my version many details have been changed and improved. Take a look on the attached pictures. To mount PCB inside the housing first you need to tilt...

This is my proposition of housing of the tape adapter of Ultimate II+ cartridge for Commodore 64. In my version many details have been changed and improved. Take a look on the attached pictures. To mount PCB inside the housing first you need to tilt...

just a small Adapter to attach the Airtag to flat surfaces with Velcro or double sided Tape.Moe infos soon!

Simply snap the adapter into the tape's holes, and then feed a chain through the hole. May require some tweaking to snap fit properly, depending on your printer. This works well and has a tight grip on the cassette when printed in ABS on my Ender...

We were lucky enough to have them, but the demo unit didn't come with the right adapter for our one-inch diameter tape spools, so I quickly designed and printed a custom adapter instead of waiting weeks for the correct one to arrive. I'm guessing...

I remixed TonyYoungBlood's Cassette Tape Case with a slot designed specifically for the cord, and incorporated JNooo's Earbud Spool into the design to manage the cord neatly. I'm grateful to both of you for sharing those files. ...Be sure to check out...

I bought a tape dispenser that was the wrong size on purpose because I didn't want to pay extra for shipping, and it turned out to be really cheap anyway, so I created an adapter to make it work with my smaller dispenser. The inside hole of the...

Adapter to use a standard tape dispenser with the Cricut 32.5mm ID heat tape rolls. Unit would also work to hold any 32.5mm ID roll in a standard dispenser. Dimensions are just under 32.55 H x 20mm W not including the support pins. Fusion...

Enclosure for the Ultimate 64 Userport expansion that attaches to the Tape port.I also made a version that allow for access to the Tape Port: https://www.printables.com/model/752267-ultimate-64-user-port-combo-adapter Print Settings:Layer height: 0.2...

This thing adapts the popular Tape Measure Yagi, or any other antenna made out of 3/4" schedule-40 PVC, to an MFJ-1919 antenna stand. ... I used the instructions here while building my antenna: https://w5nor.org/tape/amp/

A small piece to attach saw blade to the Packing tape dispenser to easily cut the tape without scissors or knife.