tarot x8 frame 3d models
105498 3d models found related to tarot x8 frame.thingiverse
This is is a bottom cover for the exposed pdb on the Tarot X8 frame. Originally it was covered by a flimsy piece of foam, and any water strikes to that area potentially will cause a short between your main batt leads. Not good. There are two...
thingiverse
This is for the Tarot X8 or X6 with the aluminum arms, will not work on carbon fiber arms. This is for mounting the ESC inside the arms, this ducts air from the rotor wash into the arms to help with cooling. The original plastic insert is removed and...
thingiverse
This is a prop holder for a Tarot X8, and they are used to snap on the arm and hold the props in place when they are folded.
thingiverse
my setup:Naze32OrangeRx DSMX 3Ch S.BUS 2.4Ghz Rx (twin long antenna version)Gemfan 5040 Multirotor PropellersMultistar Elite 2204-2300KVAfro ESC 12Amp OPTO Ultra Lite Multi-rotor Motor Speed Controller (SimonK Firmware) Version 3Turnigy nano-tech...
thingiverse
After returning from our last vacation, I searched everywhere for a 6"x8" picture frame worthy of a 6"x8" photo kiosk photo from the trip. When I was sadly unable to find anything I liked, I decided to take matters into my own hands and design one.
grabcad
Features : - Marque : TAROT - Nom de l'article: TL250H (Entraxe moteurs 250mm )- Dimensions : (Assemblée) Hauteur: 90.4mmLongueur totale: 203mm / 288mmLargeur: 220mm / 303mm- Poids à vide : 135gRecommandation d'équipements : Hélices (propeller): 5...
thingiverse
These parts were designed for the Tarot XS690 Quadcopter Carbon Frame with 16mm diameter arms. The LED holder is designed around the Quanum Quadcopter and Hex Navigation LED Light System from Hobby King and should work with the 6-Axis version as...
prusaprinters
These parts were designed for the Tarot XS690 Quadcopter Carbon Frame with 16mm diameter arms. The LED holder is designed around the Quanum Quadcopter and Hex Navigation LED Light System from Hobby King and should work with the 6-Axis version as...
thingiverse
Tarot X4/X6/X8 cover Plate for Pixhawk 2.1 with 2 GPS masts
thingiverse
Actionpro X8 camera mount with 30° uptilt for the Amax freestyle frame.
prusaprinters
Actionpro X8 camera mount with 30° uptilt for the Amax freestyle frame. Print Settings Printer: Renkforce RF2000 Rafts: No Supports: Yes Resolution: 0,25mm Infill: 100% Filament: sain smart TPU Category: R/C Vehicles
thingiverse
This is protection of frame for RC transmitter, Tarot TL2876
thingiverse
Tarot X4 Replacement Center Frame Top/Bottom complete
thingiverse
Foxtech D130 X8 V2 Frame - protective cover for 300A Ultra Power Distributor
thingiverse
I designed this to mount the safety arming switch of the Pixhawk flight controller for the tarot Ironman 650 drone frame. ...The mount is designed to be clipped onto the mount and the mount is bolted on using M3x12mm bolts.
thingiverse
I have designed this 30x30 flight controller mount for an old Tarot 650 frame, to make my own xclass drone frame. Since the default arms with this frame 16mm, and very thin for this big monsters, i moved my parts for another frame. ...But if you like to...
cults3d
I have designed this 30x30 flight controller mount for an old Tarot 650 frame, to make my own xclass drone frame. Since the default arms with this frame 16mm, and very thin for this big monsters, i moved my parts for another frame. ...But if you like to...
thingiverse
These parts are the tarot style boom clamps which are used on both custom multirotors and also some frames which are made for these in general. ... For more custom design work of all types of parts not only rc parts check my page...
thingiverse
I was getting very annoyed when taking my gopro on and off my drone So I drew up an alternative which fits snugly over the go pro
grabcad
The precision hole allign of the top frameThe countorn is simmetric , but the original one no
grabcad
http://aviatetris.comhttps://www.instagram.com/aviatetris/https://vk.com/penotetris
thingiverse
Adapter for mounting Tarot T-2D at the front of Reptile 500 V3 frame from HobbyKing
thingiverse
Lamax X8 / X8.1 Sirius Action Camera housing / open frame with GoPro mount interface. ... I designed it in the way i saw a similar GoPro Housing, Holder.
thingiverse
LED holder for Matek X8 RGB LED For spacers with Ø5mm.
thingiverse
My friend lost control of his quadcopter and the part which held the horizontal landing leg to the vertical landing strut broke. There was also a stress fracture on the horizontal landing leg , so I designed this part to replace the connector, while...
thingiverse
Customized version of https://www.thingiverse.com/thing:2404395 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2404395