taylor swift 3d model

And for many builders I consider this simpler than going the path of printing Flex material.  Model DetailsPulley and Bearing Press ToolThere is not much to say. It shows the pulley with a bearing and heat-shrink tube on the outside. The third...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0 custom_bottom_port_length = 40...

**Videos of it in Action** https://youtu.be/r5L5heNE0SI https://youtu.be/OzILwtWoT2M **What Else** Some other great models to add https://www.thingiverse.com/thing:3090510 BMG bowden mount for 3030 extrusions **Updates** **2020 Jan 22** * Better fit...

I would recommend all the bridges honestly. Update Jan 31 2021made the holes for the hex nuts smaller to promote better hold under torqueadded relief cut on the M6 hole, as threading may result in splitting the model on version D1resized the D1...

And get your supports in order first, the models need a relatively precise and flat supported surfaces. <font size="3">The modification uses many parts from the original setup, but the PTFE tube must be cut, making this a non-reversable mod...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The casing has a channel modeled in the side to accommodate the ribbon cable coming out from the Raspberry Pi. 3) Insert the smaller end of the ribbon cable into the Raspberry Pi Camera Module, then place the module into the view port. The view port...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_y_position = 0 custom_top_port_x_position = -10 use_stencil = 1 pattern_line_thickness = 20 stencil_pattern_element_shape = 3...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_left_port_length = 50 custom_top_port_corner_radius = 5 pattern_element_rotation = 0...

First, I modeled the front of the display to fit the RepRap Discount Full Graphics Smart Controller. Then, I also decided it needed a back to protect the circuit board. Easy peasy! Next, I tackled the problem of mounting a TFT35 touch screen...

Both versions comes with an extra split in half model, depending on your print preferences. If you glue a cow to the ground plate as prop, remember to place it where the UFO won't crash on it's head…</p><p>&nbsp;</p><p><strong>My UFO doesn't crash...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Once I get the sizes right, I'll upload the fixed models. <b>23/03/2020</b> (3) Just uploaded some slightly altered versions in an attempt to use them as actual particulate filter masks. The new versions have a single vent hole which hopefully will...

... glue works for you on PETG. I have made extremely good experiences with YUKI MODEL superglue, which gives me basically unbreakable connections between PETG parts. The mounting plate and the counter plate are very simple to print on their flat sides.

Note: these videos are uploading slowly, so they might not be fully processed when I publish this model. They should be available in a few minutes.</p><figure class="media"><oembed...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame which require support. You may need to use a raft or brim to secure the part...

This model is for a “streetlight-style” wired garden/pathway light. Brighten up your garden path with lights, without spending a fortune on MoonRays or similar products where a single lamp can cost up to $20! In bulk I can make these for about $3-5 a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

Presupported in 32mm and 75mm scale [Medium Model Size] [Statblock included in our 5E Campaign: The Sightless Seer]   Born blind to noble parents, Irivyl was kept cloistered for many of her earliest days. When she drowned within the Prendael River as...

The model is amazingly easy to fly. https://www.youtube.com/watch?v=rsS5YetUQyA The video quality is less good - this time I had to film myself. There are two hull versions. The longer version (lv) is the one shown in the picture and video. But...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 27...

The color thicknesses and the width of the outline stripes on this test print match the stripes on this case and future cases I upload will probably use similar...

We successfully engineered an incredibly stable and secure mounting arrangement by adjusting the RC roof rack's structural reinforcement through computer-aided engineering models. By applying advanced design methodologies, our innovative product not...

... and presupported version. This product contains the following parts: 80mm Base Body Legs Cleaver Arm DnD 5E Datasheet Get a 40% discount on this model by joining my Patreon! You can also order physical copies at my shop on Only-games! ...  

I modeled this in Fusion 360, and you can find the source files as well as IGES included. I printed it in PETG since that's what was in the printer. The infill was 30% with three solid layers. ... Print Settings: Printer Brand: MakerGear Printer: M2...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_y_position = 0 custom_top_port_x_position = -10 use_stencil = 1 pattern_line_thickness = 30 stencil_pattern_element_shape = 3...

The initial idea was to couple the two 4020s to the original TTBluer case, however it has lower flaps that made the process difficult, as I wanted to preserve the original part without cutting flaps, I decided to model a new case. I have results...

I hope this piece works for you; it was actually the most challenging to model and get right. 9. You should be good to reassemble now! 10. Put the hammer-trigger-piston assembly back in. 11. Lay the cylinder back in place, including the U-clip for...