tcl tv stands 3d models
170600 3d models found related to tcl tv stands.thingiverse
this is a shorter and simpler version of the 3DbyJB TCL ROKU tv leg. this will fit 40in and 43in TCL Roku tvs. ...
prusaprinters
Fold-able legs/stand for TCL TV so that you can fold them in and hang the TV on a wall (I have a wall mount I will share seperately) Category: Replacement Parts
thingiverse
Fold-able legs/stand for TCL TV so that you can fold them in and hang the TV on a wall (I have a wall mount I will share seperately)
thingiverse
Designed this for my TCL TV with a 10mm thick border. ONE LAYER contains bridging. ... .2mm
thingiverse
This spacer is meant to raise your TV off of the stand. In my case I use the TV's for side PC monitors and wanted to raise them to be level with my actual gaming monitor in the center of the two. By default, these are .625" high, but you can...
thingiverse
I designed this to hold my sound bar. ...If you look closely at the top of the tv, it has a slight forward slope. ...That and the curved back, required some accurate measurements and a few iterations.
thingiverse
Simple holder for remote control of my TCL TV. You can use 2 screws to fix it to the wall. Works fine. ... Enjoy ;)
grabcad
TV support used to raise the TV in order to place the soundbar below and not interfere with communication with the remote control.3D printing support is difficult to remove. ...Minimum filling of 25% recommended
thingiverse
Stands that fit under the TV's provided legs so the Cable box can sit below the TV. The Samsung has 140.5mm between the posts. The Visio is 188mm. Fusion360 files shared below. ... Samsung TV riser http://a360.co/2wKtRVu Visio TV riser...
thingiverse
This mount allows you to set a TCL 43" 4K TV on its back for the purpose of using it as a digital gaming table to display maps. The height matches the bottom section of the TV so you only need two prints to hold the top corners for the TV to lay...
thingiverse
... accept them (filesize), but you get the idea. ...It sits on top of a TCL TV perfectly. It's a 12mmx12mmx12mm rectangular holder and you can screw your wyze cam pan v3 to it. Super simple stuff, no bridges or supports. ...Print it however you want.
thingiverse
... accept them (filesize), but you get the idea. ...It sits on top of a TCL TV perfectly. It's a 12mmx12mmx12mm rectangular holder and you can screw your wyze cam pan v3 to it. Super simple stuff, no bridges or supports. ...Print it however you want.
thingiverse
This is a replacement battery cover for a TCL Roku TV remote. There are several versions of Roku TV remote, so this may not fit yours. The STEP file was included in case you'd like to adjust it to fit yours. The Airtag cover is still not perfect....
thingiverse
A simple remote holder for TCL brand Roku smart TVs. ...Mounts with either two screws or adhesive similar to a command strip.
thingiverse
A simple remote holder for TCL brand Roku smart TVs. ...Mounts with either two screws or adhesive similar to a command strip.
thingiverse
My sons TCL 43" Roku Tvs base legs were to short to fit his Xbox One and cable box under it so I designed 70mm tall ones and printed them on my Ender 3 Pro. ... These fit perfectly using the existing screws.
thingiverse
Based on https://www.thingiverse.com/thing:4253124, however upon testing, these feet did not fit or work with my TCL 55S425, so I designed and printed some from scratch. Then I added a sound bar and made the extenders to allow for the remote to...
thingiverse
This is a replacement battery cover for a Roku remote for TCL TVs. I made this because I hate searching for the remote, and I didn't want to buy a new one that does allow tracking. As a side benefit, the extra length makes it easier to grip the...
thingiverse
... recommend using a plastic of high strength with a high infill percentage. The idea of this was still designed with some sort of support underneath (like a shelf), but with proper layering and infill these could support the TV on their own. ...
prusaprinters
Requires two additional screws to mount the soundbar onto the part (in addition to the two screws to mount the whole thing to the TV). I initially designed it to where a part of the print fit into the back of the soundbar and no screws were needed,...
thingiverse
Since I have a TCL Roku 4K tv, I have to use IR when it comes to controlling the volume on the TV. The Apple TV has to be visible, so I decided to take an Apple TV mount, and put brackets on it to fit the TV. It worked quite well. The reason the...
thingiverse
I wanted to mount my Klipsch Icon SB-1 sound bar to my TCL 40" Roku TV, made this mount that screws perfectly to where the TV stand would attach. At 75% in-fill they are very strong. Same idea should work for other sound bars, I got lucky that the...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/5VGfBQzNZLc
thingiverse
Mount Altec Lansing 5100 speakers to the foot mounts of a hanging TCL TV. ...Also includes simple cradles for the rear speakers.
thingiverse
Unfortunately when we were going to put those on the remote we noticed that the TCL Roku TV remote does not have any real flat side for that. I found this great model for a TCL Roku remote holder and changed that up to have a place for the Tile...
prusaprinters
TV is a TCL 55" 4K HDR (2017) SB is a LG LASC47Printed in GST3D PLA+ 0.2mm layer height40% gyroid infill 4 perimeters6 top/bottom layers I (or you!) may consider printing this in ABS+ or PETG if it deforms over time but so far PLA+ has...