telescope tripod spreader 3d models
18881 3d models found related to telescope tripod spreader.thingiverse
I found it annoying that the tripod spreader (lens/accessory tray) that came with my Celestron Nexstar 8SE telescope needed to be removed to fold in the legs, and also was a little too wide to fit in some tripod carrying cases. ... So I designed this...
pinshape
this is an ABS replacement arm for the celestron telescope tripod spreader
thingiverse
This is a part acessory for a Celestron Powerseeker 70az Telescope Tripod. I have printed it in 20% infill with supports. Print 3 supports for each base. ...
cults3d
Parts to repair a Libec tripod spreader. Bottom pad and bungee printed in TPU, the rest in hard plastic. extras required, M6 x 50mm screw, nt & washers, M4 x 45mm, nut & washer. (A couple of handle-bar grips, to fit 22mm dia. ...bar, are also included:...
thingiverse
...https://www.amazon.com/gp/product/B07546NKR8/ref=oh_aui_search_asin_title?ie=UTF8&psc=1 The challenge was figuring out what to do with the tripod spreader piece. It can't stay on the tripod and I certainly didn't want it bouncing around in the case.
thingiverse
I will be using aluminum U channel and clamps to create the entire spreader. I'll post a pic when its done. ... I printed in the original thing after scaling it to 80mm in diameter and it will work, but again, I wanted that central mounting hole...
cults3d
The part requires bungee cord* or flexible clip (included STL, printed in flexible plastic - eg TPU), though even a few strong elastic bands will do the trick..) The foot is designed to support the tripod with a 50mm M6 bolt (which goes through...
thingiverse
It's customizable so you might be able to get it to fit another tripod of similar sort. I had to cut the rivets that attached the old hub, and I used #4 screws to attach the new one. ... This uses and bundles my [tube mesh...
thingiverse
... still usable but I figured why not make something. Uses part of the telescope tripod, with bolt and side bolt for locking in rotationg (though I could do that with camera tripod) then uses the existing camera mount 1/4-20NC and the side locking pin.
thingiverse
Not sure if this will be useful to folks, but this replaces a broken bracket on the crossbrace of my telescope tripod.
thingiverse
have an old tripod and a cheap kids telescope that I have had for a very long time and wanted to mount it on the tripod for more stable and accurate viewing tripod mount 2 should be more stable tripod mount 1 you can just modify to fit your needs
thingiverse
Quick mock up parts for the Saxon telescope tripod. Print good with strong plastic as its taking a lot of weight. ... Part 4 should be taped to M8x1.0mm
thingiverse
I believe this tripod is the CG-3, so any telescope that uses it should work. The levels I used are 9.5mm diameter x 31mm long cylindrical level bubbles. We had them lying around so I don't know where to source them. They should just slide in with...
thingiverse
I have a Celestron Spotting telescope, and a nice tripod, but it only has one anchor point, so the telescope has a bit of twist and wobble. I designed this adapter so I get a more stable mount. Be sure to print it upright, because you don't...
thingiverse
This is a telescope mount to be used in camera tripods. It is meant to be glued to the telescope so it may only be suited for someone wanting to make a telescope on the lowest budget possible like I was. SoporteTelescopio.stl is what I used for a...
prusaprinters
This model is a replacement bracket for a telescope tripod, it is almost an exact fit to the original bracket. ...To print, orient the open side upwards and add supports to the overhang at one of the ends. </p>
thingiverse
Add 1/4 hex nut (Standard for most of the DSLR tripod) and you are good to go. ...Print two and join them with 3mm nuts and bolts on side or just print one and superglue it on bottom of your 50mm telescope tube. ...Works either way.
prusaprinters
I believe this tripod is the CG-3, so any telescope that uses it should work. The levels I used are 9.5mm diameter x 31mm long cylindrical level bubbles. We had them lying around so I don't know where to source them. They should just slide in with a...
thingiverse
This is a telescope adapter. this is also my first upload . ...thank you...
thingiverse
These are intend to be used with the tripod anti-vibration (vibration reduction suppression) pucks pad to make fine tuning adjustment to level the feet/tripod
thingiverse
A holder for my tablet that clips to my tripod while I polar align or just a place to store it. Print two. The tablet will slip between them. I put a small piece of Velcro below the bottom holder so it would not slip down. ...This is designed for a 10"...
thingiverse
When the spreader from Sachtler tripod breaks, the reason is often the star joint in the middle. Number part ssp10e0106 for spreaders SP75 7001 and SP100 7002. I haven't printed yet, just design it in Blender. When I print it i'll comment.
cults3d
mid-spreader, to lock on to a 6mm dia pin with a centre boss on the tripod 1 inch (~26mm) wide (similar to Cartoni tripods): Requires: 3x Aluminium bar 11.5 x 2mm (nominally 12x2mm), approx 30cms long. + 6 off M3 or M4 screws and lock nuts. (or you...
thingiverse
So, I bought a second-hand Celestron NexStar 4E - it is in pretty good condition, but is missing the spreader which firms up the tripod legs - so i decided to make one. My 3D Printer has a build area of 100 mm x 100 mm, so it needed to be made in...