tenlog tl d3 pro 3d models

Spool Holder for Tenlog TL-D3 Pro or any other printer that uses 20mm rails -- no support needed.

I built my version To match my Tenlog TL-D3 Pro Filament detector support for the Tenlog TL-D3 Pro First put the detector in place on the support, this will then find its place on the VGA connector, then a clip inserted on the cable comes to secure...

FILAMENT SWITCH TENLOG TL-D3 PRO connector assembly mirror print for E1/E2 3 screws M3 5mm + 20mm printed in 0.3mm PLA FILAMENT SWITCH TENLOG TL-D3 PRO DUAL V2 direct mount on Extruder mirror print for E1/E2 printed in 0.3mm PLA 20% infill 2 Screws...

I created a little bin to sit behind the nozzle brush on the Tenlog TL-D3 Pro. this little cup collects the small ooze of filament from the nozzle from when it's heating up, or waiting for the next layer. For dual extruder, print 2 bins in mirror...

I noticed the feet on my Tenlog TL-D3 Pro weren't giving my printer enough airflow for my liking, as the power supply was getting warm to the touch. I quickly designed a basic "foot" for the printer. Simply print 6 (one for each existing support...

The [Nozzle Stopper](http://www.thingiverse.com/thing:3748488) has been working very well for me though.** Wipe Bucket for the Tenlog TL-D3 Pro. ... Simplify3D Tool Change Script ``` ; Tool Change Start T[new_tool] G92 E0 ; Reset Extruder G91 ;...

This is a simple webcam mount that attaches to the side of the Tenlog TL-D3 Pro. It's remixed from a CR-10-compatible model that I've used for a long time. **Attach to Printer** This attaches to the printer using the mounting holes in the power...

TENLOG TL-D3 PRO Z STABILIZER Remove the original leadscrew Assemble the new top brackets (use the same nuts and screws) Remove the electronics cover Remove the two rear screws on 4020 profile to fixed the bottom support Assemble the z_bottom support...

TENLOG TL-D3 PRO Z STABILIZER ================================ To download all project click in this link https://www.thingiverse.com/thing:4948291/zip - Remove the original leadscrew - Assemble the new top brackets (use the same nuts and screws) -...

... and the 8mm M4 T nuts (and split washers) or 8mm M5 T nuts on the top. This requires no supports but a brim is advisable. This is primarily designed for the Tenlog D3 Pro as it would be difficult to put T nuts in both top and side of the extrusion.

replacing the tenlog motherboard with a duet 2 wifi + duex5. ...modification in progress

Filament Abstreifer für Tenlog TL-D3 Pro links für rechts Spiegeln Form für Silikonabstreifer Nozzle scraper HT Silicon

For the most up-to-date version, see https://github.com/jonpackard/3d-printing-profiles I created a PrusaSlicer profile for the Tenlog D3 Pro (TL-D3 Pro). I used the information from the Cura profiles provided by Tenlog. See photo for 2-color...

This is a drool catcher for the Tenlog TL-3d pro. It catches from both directions, before and after the wire brush. I printed with tree support only connected to the build plate. ...

Un support caméra Playstation Eye pour l'imprimante TL-D3 Pro. ... J'ai diminué l'épaisseur à l'endroit du maintient de la vis pour laisser passer le plateau.

Print on back, supports if you need them.I did not make any brackets to mount the circuit board, I threw all the Tenlog electronics away and use can-bus.I printed it on the quick with a 1.0mm nozzle and it worked fine. Remove the big heavy...

This is a remix based on https://cults3d.com/en/3d-model/tool/bltouch-bracket-mount-for-tenlog-tl-d3-pro - thank you ELABORATEJ for this nice model! I've changed the arm mount to use an M3 screw and locking nut. ...Not as nice looking as the original...

The Tenlog TL-D3 Pro with the BMG extruder upgrade is a great machine - but ours had a slight issue recently with the extruder lever breaking, I think due to a clog. I reached out and collaborated with the awesome folk @ LNL 3D Solutions, and I was...

I'm not a big fan of the stock light blue cap that comes with the Tenlog TL-D3 Pro, so I set out to make my own. I went through several revisions to try to get to the right fit. This revision comes out super tight, but I decided that I'd rather have...

I created this camera mount base piece to mount a camera on my Tenlog TL-D3 Pro using the diagonal vent slots in the base of the printer. Printing requires supports, and you will need to do some cleanup after removing the supports. The screw in...

... glass since it does test the 300x300 perimeter as well as a line up the middle. 12ap2020 - Added a D3 specific splitter that includes the void area down the middle that should be voided when in "mirror" mode otherwise the two extruders collide.

... glass since it does test the 300x300 perimeter as well as a line up the middle. 12ap2020 - Added a D3 specific splitter that includes the void area down the middle that should be voided when in "mirror" mode otherwise the two extruders collide.

There are quite a few nozzle wiper / prime bucket designs for the Tenlog TL-D3 printer on here, but Tenlog now produce their own metal version that can be purchased through their online retailer for a very good price here:...

deutsch/german Cura 5.2.x - Profil für Tenlog-Drucker einfach den resources-Ordner in den Unterordner vom Programm kopieren: bei mir ist dies zum Beispiel: C:\Program Files\UltiMaker Cura 5.2.2\share\cura\ english Language Cura 5.2.x - Profile for...

I added some fillets for strain relief and increased the size of the slots for the wire brush. ... This is a remix from https://www.thingiverse.com/thing:4070675

Based on original fan shroud. It has better access to the hotend and more clearing in front to view nozzle. It fits up to a 40x20mm hotend fan with sufficient clearance to hotend. Print in PLA/PETG upside down, 100% infill with support. ... UPDATE - V2...

Based on original fan shroud. It has better access to the hotend and more clearing in front to view nozzle. It fits up to a 40x20mm hotend fan with sufficient clearance to hotend. Print in PLA/PETG upside down, 100% infill with support. ... ...

3 magneti 8x3 mm

This will slip over your filament spindle and interface with the end of it. ...Keeps your roll from being pulled off if you have moved your holders to the side as I have.

This will print for E2. Print mirror image for E1. To complete, You will need: 20mm pcb hex standoffs @3 Misc 3mm screws 1.5mm (cant remember exactly, I'll edit later) screws (amazon computer screw assortment) 32mm led ring 53 mm fan and 40...