tent pole connectors 3d models
80185 3d models found related to tent pole connectors.thingiverse
This connector allows you to join a tent pole (with a J adapter) to your caravan, roof racks or other solid surface. Use screws or rivets to attach to the solid surface. Accepts M8 bolt with a captured M8 Nut. Nut will push-fit and should be snug....
thingiverse
An older Wenger steel pole kitchen tent was missing three out of four of the corner pieces after some severe wind damage. Ender 3 to the rescue! I wasn't sure if the PLA would be sturdy enough but these parts were tested in high wind conditions and...
thingiverse
Receives 3/4" Poles Height: 3.75" (95.4mm) Width: 6.3" (160mm) Length: 2.7" (68.2mm) Recommend a very solid print as it takes a lot of pressure when the tent is assembled. Supports should be used during printing for the best results. ... Settings I...
thingiverse
My Son wanted a Tipi Tent so I designed some connectors for 16mm diameter wood sticks. I think you can get at any Hardware Store. In my Case, it was the leftover from a converted IKEA Baby bed from my daughter.(see background). The 15 sticks in my...
thingiverse
Sand plate for a Tent Pole (or to stop poking through the tent floor)
thingiverse
tent pole clip useful for folding campers e.g. ...conway and pennine 19mm pole diameter
thingiverse
I bought an expensive REI tent for cheap because it came with a broken tent pole. So here is a flexible tent joint to replace the inner connector piece that was broken. There is an inside draft angle to keep either side from pushing through too...
thingiverse
This can be used to attach 8.6mm tent poles to triple layer coroplast laminate.
cults3d
fixed camera tripod. ... to assemble with 9mm igloo tent poles. ... to assemble with 6mm screw
thingiverse
But could be used to replace any fittings for your tent poles, if they are the right size. Have hollowed out the part that goes into the pole to save print time. Doesn't reduce strength significantly. Use a screw or rivet through the pole to keep...
thingiverse
Just a cap that goes over the pointy end of a tent pole, with an eyelet to hang a light from.
thingiverse
Hook to hang items in a single pole style tent. I developed this hook to work with 3/4" dia. Easton aluminum tent poles. These clip on and will not slide up and down when in use. Print 3 perimeters, 20% infill, ABS, PET-G or Nylon. ...
thingiverse
This was requested from a friend that lost his tent pole insert. This is the part that the elastic cord connects to that holds the other poles together. It's for a pole with an inside diameter of a little over 1/4". ... The model diameter that inserts...
thingiverse
... enough to provide the support I needed and it was to big to fit snugly on the pole. My son and nephew were horsing around and crashed into my sons indoor tent and broke the pole. ...I used this along with some hot glue to repair the broken pole.
thingiverse
I am using these foldable tent poles from Aliexpress. I was worried about them poking holes in my outside tent, so I made this dome cover for them. ...
thingiverse
Fits onto the end(s) of a 9.5mm inside diameter tent pole to attach the shock cord onto. ...Print with the flat end facing down onto the build plate, no supports needed.
thingiverse
The original pole clamps to adjust the tension inside the tent easily break when too much force is applied. ...As these clamps cannot be ordered seperately I tried to construct a simple alternative clamp.
prusaprinters
... make hanging lights in your Clam Quickset tent a snap! ...Clip them onto the poles for a quick easy hook to hang lights or other lightweight items from. ...I needed 6 for the poles in our Pavilion Quickset Clam.Print in PETG 0.3mm MK3s+ no supports
thingiverse
I snapped an ~8.7mm tent pole, and the design of the pole assembly makes it impossible to replace a single pole without buying a whole new pole assembly. So, 3d printing to the rescue. Print in 2 pieces, and they form a splint around the broken...
thingiverse
This is designed to go on top of a tent pole, positioned in the middle of a tarp to keep the rain from collecting. There are rings to tie lines to either keep the pole in place, or to stretch to a corner pole to hang items around the campsite. ...
thingiverse
Tent pole support to prevent poles without an end cap from: * sinking into the ground * getting filling with soil There's an incline, to help the pole self center. A small hole is placed in the middle to drain rain water. Note; the support in the...
thingiverse
Edit it online https://www.tinkercad.com/things/6RHOWUmbUMo It is to connect tent poles together, the original ones are not available anymore (The tent is probably 30+ years old) There are two tops here one at 22.5mm diameter and the other 26.5mm. ...
thingiverse
I remixed my tent hook design to make a holder for a portable battery power bank that I use to power the LED lights in my tent - I have a LED strip that I have spiralled around the top section of the pole, and up to now I have held the battery in...
thingiverse
... with 50% infil using PLA, so I haven't bothered to use another plastic. As far as I know it's holding up well. I have no idea what the brand or model the tent was, but figured maybe someone would end up in the same situation and could use this.
cults3d
This is a pole hook which is designed to be used for a pole with 15.5mm diameter. In my case i used double sided tape to fix various objects such a humidity meter to the hook. Check my profile for more useful hooks. There are two version. The 16mm...