terrarium light 3d models
212804 3d models found related to terrarium light.
myminifactory
Made this to stick on the roof of my glass terrarium (dubbel sided tape) infront the build-in socket so the bright UVB light doesn't make me go blind. NOT FOR HEATING LIGHTS! ...Only for lights that don't give off a lot of heat.
thingiverse
Made this to stick on the roof of my glass terrarium (dubbel sided tape) infront the build-in socket so the bright UVB light doesn't make me go blind. NOT FOR HEATING LIGHTS! Only for lights that don't give off a lot of heat. Best printed in a...
prusaprinters
<p>The bulb holder for the Reptiles expert UVB is designed to hold the bulb in the mesh using the top part. A circular hole with a diameter of 110mm needs to be cut in the mesh. ...At the same time the ceramic sleeve needs to be inserted into the...
thingiverse
A stand to hold a light bulb with a mini terrarium inside. Update: added "leg part v.2" (thanks to SirLucian for the idea) for the ones who don't want to use brass insert and screw to assemble this thing. The peg has 0.2 mm of tolerance so...
thingiverse
This was made as a light fixture for a carnivorous plant terrarium jar. ...
thingiverse
I wanted the perfect lighting setup for our bearded dragon's 40 gallon Zoo Med terrarium that we purchased from PetSmart. Unfortunately, they only have the dome lamps that only cover one third of the terrarium's total length. We wanted a lighting...
cults3d
A big terrarium cave! A hide for your reptiles - gecko, snake, lizard, phelsuma, crested gecko, agama. Made in TINKERCAD. ...Enjoy your tera-prints ;)
cults3d
Terrarium for a 106mm diameter bell An irrigation system is provided so that water can flow to the bottom of the pot.
grabcad
My newest project is a thing I want to build, a new home for my Correlophus Ciliatus/Crested Gecko, a terrarium 50*60*100 cm. ... There will be A LOT of interior in form of bits and pieces of Styrofoam.
thingiverse
Glass dimensions: Moving top: 196x110x3mm Doors: 125x198.4x3mm Front: 47x200x3mm Sides (2szt): 197x200mm Back: 194x197x3mm Top: 60x200x4m Top Vent(optional, you can order perforated sheet or just print it ) : 30x200mm With this dimensions you will...
prusaprinters
I highly sugest printing parts in Prusament PETG, because PLA broke too easily.Glass dimensions:Moving top: 196x110x3mmDoors: 125x198.4x3mmFront: 47x200x3mmSides (2szt): 197x200mmBack: 194x197x3mmTop: 60x200x4mTop Vent(optional, you can...
cults3d
Small terrarium for an insect or animal of small dimensions. In it I have even had praying mantis, stick insects. It has a container at the bottom to fill with soil and put plants. It has dimensions of(11x20x39 cm). It is composed of machined...
cults3d
Here is a mini terrarium for jam jar type "bonne maman" with a diameter on the thread of about 80.6 mm. A good layer of clay logs or gravel should be put on the bottom before adding the soil. Once the plants are installed and watered, simply screw...
prusaprinters
I designed this to fit under a glass container that I found at Kmart and makes for a perfect mini Terrarium/Mossarium lid.I printed it with 6 walls to help ensure it would be water tight and this seems to have workedI will continue to tweek and think...
thingiverse
... cover with 4 magnet with the lengh 5x3mm. Acryl glass width: 3mm Anycubic Chiron Filament: PLA Temp.: 210°C Speed: 40 mm/s Support structure: no Pressure plates adhesion: Brim 5mm Time terrarium: 5 hour 40 minutes Time cover: 1 houer 20 minutes
sketchfab
Environment created in Maya, Unreal Engine with texture made in Substance painter. ...(I made floor and grass inside Unreal so sadly could not transfer them over)