thorens td 160 3d models

The vital components for several Thorens turntables are the hinges parts. Three essential files need to be printed: The upper hinge pieces, cerniera_sup, require printing two identical units: one left and one right. The lower hinge sections,...

Mounting adapters for integrating a Thorens Turntable onto a standard base. ...Primarily designed for use with the TD-160 lineup of turntables. ...Unsure which other Thorens models these spacers will accommodate.

Thorens TD models PLINTH STANDOFFS / FEETS -fits similar models -inner hole is 3 mm does fit the original screws + washer -overall height is 7 mm no supports can mod the file if you need

Just a quick model i made to indicate the 33, 45 and 0 settings for the speed knob on a Thorens TD-165 Turntable. ...You will have to experiment with settings to best print it out

I have had my Thorens TD 280 turntable sitting in a rack for years. For this I had removed the cover. Meanwhile, there is that rack no longer. I had kept the cover, but the hinges are missing. Since I now want to use the hood again, I have...

The Thorens TD 160 uses a mains synchronous motor paired with a double pulley to switch between 33 and 45 rpm. This same setup applies to other Thorens turntables as well. To play shellacs at 78rpm, I created an adapter pulley that fits onto the...

This replacement part is specifically designed for Thorens TD-160 and TD-165 turntable series, as well as their sibling models like the TD-145. While some additional work may be required to perfect it, this part should still be usable by those in...

Adjustable base for the (Thorens) Q-Up Tonearm lifterThe original base for the Q-Up tonearm lifter is shaky and doesn't stay in place.Here is a better base:horizontaly adjustable with a screwvertically adjustable with credit card slicesa wider foot...

The Thorens TD 240 turntable measures H-130mm, D-430mm, and W-365mm. The model is created using 3DMax 2014 V-Ray software. The archive includes FBX and V-Ray formats. Units are measured in millimeters, and all textures have unique names. ...This model...

These adapters fit snugly into the recessed hole in the platter of Thorens TD-165 and TD-166 turntables, although they may also work with other models as well. My goal was to provide a solution for people who are searching to replace these rare lost...

This is Realistic High Detailed 3D model of THORENS TD 295 MK IV TURNTABLE with a Vinyl.

The Thorens TD 240-2 turntable measures H130mm, D430mm, and W365mm. This model was designed using 3DMax 2014 V-Ray software, with the archive containing FBX and V-Ray file formats. All measurements are in millimeters, and each texture features a...

THORENS 35 / 45 turn disk centerer td166 MKII VINYLE

Thornes TD 160 arm rest light

Realistic model turntable.

Realistic model turntable.

After more than 20 Years, the original audio cable went bad because of too much oxidation. ...I replaced it with a other high quality one, but the strain relief was fixed to the old cable.This model supports a GND shield line, too.

90 - 260V 50/60Hz

thorens classic logo

Rega armboard support fit on thorens TD 145-46- 160-66

Thorens TD124 Armboard & Thorens TD 124 armboard for SME 3009 Series II Improved never printed. ...To try

Very big size Thorens turntables logo.

Thorens control knob replacement designed specifically to fit a wide range of older Thorens turntables.

Just snaps on (held by friction). Should be fully customizable. ...Print Settings Printer: refit tabletop cnc mill Rafts: No Supports: No Resolution: 0.4mm nozzle, 0.2mm layers Infill: 100% Filament: Sopytka PETG Category: Household Supplies

Simply snap it into place - no tools required, thanks to its clever friction-based design. ...This innovative system allows for total customization to suit your every need.

Armboard for Thorens TD124. Design based on original measurements, never printed. ...

THORENS TD125 Plinth drawing. ...This contains all the dimensions for an original plinth.

I did a hinge to Thorens dust cover because the original its too thin to print and will broke easy. So i create my own version. I did with Sketchup 2018. I share the original file maybe you want to do a remix. ...

The Thorens turntables mounting the TP62 tonearm (TD145MKII, TD147mkII, TD160mkII, TD166mkII) need an higher tonearm holder in order to park the tonearm with the lifter up. This design is 8mm higher and a bit thicker, in order to make it robust...