thorlabs det210 3d models
128 3d models found related to thorlabs det210.thingiverse
The threads for the battery compartment on a det210 from thorlabs must have galled. I forced it apart since the device could no longer be biased with a dead battery. Realized a 9V battery would be easier to replace than the original battery was, so...
thingiverse
This is an adapter for 1 inch round optical filters (e.g. ...Thorlabs) for installation instead of standard 2x2 inch square filters (e.g. ...Thorlabs)
grabcad
Houses electrically contolled fiber-optical attenuators like Thorlabs V800PA and similar.
thingiverse
The tripod mount was getting tipped over and was difficult to precisely locate and rotate, so I printed out an adapter that grips the tripod tube (minus the tripod legs) and mounts to a ThorLabs PR01/M rotation stage. ... I included the F360 design...
thingiverse
This is an adaptor to mount ELL9 control electronics from Thorlabs to an optical breadboard. The design is only to assist prototyping to accommodate the electronics avoiding shortcuts with the optical breadboard. I added a single hole for M6...
thingiverse
... offset (in millimetres). The offset is a value _added to the diameter_ in the range of (-1 mm, 1 mm). Find more about the insert in its [GitHub page](https://github.com/bionanoimaging/UC2-GIT/tree/master/CAD/ASSEMBLY_CUBE_Thorlabs_v2). ...
thingiverse
mounting bracket to connect Thorlabs 25 mm constructino rails. ...It's the tiny grey thing in the middle of the image on the inside of the left cage
thingiverse
Instructions This model was created (not merely taken from the ThorLabs website, where it is available as a .step file) in SketchUp using dimensions provided on the ThorLabs website along with some guesses at the underlying construction geometry. I...
thingiverse
Organizer for your 6mm rods from Thorlabs. ...Additionally i glued small transparent box from side for the screws.
thingiverse
Inexpensive alternative to official Thorlabs equipment, plus doesn't scratch as much. ...Print in pic in PC/ABS at 0.19mm
thingiverse
This a beamsplitter cube adapter for Thorlabs B4C Kinematic Cage Cube Platform. With the adapter, the beamsplitter cube can be mounted upside down for easily adjustment. ...A shapeways version is also available at...
thingiverse
This is a guide/spacer for Screw alignment if you're looking to use Thorlabs BA1/M to compensate for the lost in Z height (10mm) when upgrading to Kodama's Leveling bed. ...
thingiverse
Just simple organizer for your 1/2" or 12.7 mm post holders from Thorlabs. ...Posts3 file is only different in front face that is perpendicular to the plane.
thingiverse
https://www.thorlabs.com/newgrouppage9.cfm?objectgroup_id=5786 We have a couple cubes that we use. We keep our cubes in this when they aren't in use. It keeps the dust away from the filters and the filters protected. It has a .25" through hole in...
thingiverse
Dust cap and laser reflection dump for Thorlabs cage filter wheel [CFW6/M](https://www.thorlabs.com/thorproduct.cfm?partnumber=CFW6/M#ad-image-0). The print prevents dust accumulating on your filters if the wheel is mounted horizontally. Also,...
thingiverse
When you use a Thorlabs kinematic mount to hold a mirror, the reflecting surface is displaced from the center of the mounting post. As a result is not easy to align the input and output beams using the grid of the optical table. ...This simple piece...
thingiverse
Cable-tidy box for use with thorlabs GVSM001/M or GVSM002/M systems. Screws directly to the card driver cover (requiring slightly longer screws than supplied with the cover). Version 'c' has space for a single insulated BNC bulkhead connector.
thingiverse
Two adapters for goniometer (tilt adjustment device) [GN1/M](https://www.thorlabs.de/thorproduct.cfm?partnumber=GN1/M) from Thorlabs. 1. Ring adapter to mount 2-inch (diameter) lenses on the goniometer. The optical axis is 1 inch above the top...
thingiverse
I needed to apply a counter-torque on the rotation axis on a Thorlabs MFF102 flipper mount, and there was nowhere to apply this force. Therefore I created this connector which hooks up to the spare mountpoint on the flipper and creates a central...
thingiverse
A mounting plate to allow Thorlabs' DCU22xxx USB CCD cameras to be mounted using a M4 screw. ... Instructions I print this on a Makerbot Replicator 2 using 3 shells, 10x infill, no support, no raft.
thingiverse
this is a cover for standard Thorlabs 30 mm cage system. ...If made from black opaque material protect optical system from backside light, may protect user from laser irradiation and protect the optical system from dast.
thingiverse
**Summary, purpose** Enables mounting the TILL photonics lightguide condenser (27 mm diameter) with Thorlabs SM1 rail system. **Things you need additionally** * This item does not contain threads. Threads are aquired by inserting M3 nuts (5.4...
thingiverse
A simple mount for the Thorlabs style 30 mm cage system that is based on 6 mm diameter rods. ... It either mounts a cage onto a post or plate with an M4 screw or bolt, or it can even join two cage systems together because of the pairs of cage-rod...
thingiverse
This is an improvement of a previous Centering plate for Thorlabs kinematic mirror mount (thing http://www.thingiverse.com/thing:259018). When you use a Thorlabs KM100 kinematic mount to hold a mirror, the reflecting surface is displaced from the...
thingiverse
Inspired by Tjsangster's peep hole cover, I added a Thorlabs-style 30 mm cage mounting so I could use it in an optics lab. It's a nice quick 30 minute print :) **Don't use it to block laser beams without testing it first** (with a *significant*...
thingiverse
A 30mm ThorLabs cage system part to mount a pinhole with XY positioning micrometer screw knobs, a fixed pinhole mount or even a blank cage part for blocking light. This fits well in the cage system allowing the pinhole distance from the light source...
thingiverse
Reduction from the Thorlabs cage system to KS1 precission kinematic mount. Is great if you want to couple light in a cage system into a fiber, but don't have proper cage fiber collimator mount. ...You can then use something generic like KS1 to do the...
thingiverse
This is a standard optics clamp with a slot for 1/4''-20 screw. It's designed to be non-magnetic and non-conductive so that it can be used in the vicinity of a SERF magnetometer. Compatible non-magnetic optomechanical parts: ...