threaded rod support 3d models

Hypercube Threaded Rod Support This only works if your threaded rod reaches the top 2020 rail. You will need a 8mm bearing to press in. Printed with my Hypercube: .1 layer height and 50% infill. ...Should be fine with .2 or better.

Foot to add 1/4 x 20 threaded rod as a support in the middle of long rails.

Nut trap to go along with the threaded rod support foot. Designed to work with 1/4 x 20 rod and fit inside a 3/4" EMT conduit. ...Can use a 1/4" piece of rod in the end to help slide the nut trap into it's proper location.

Designed to take both 8mm & 10mm threaded Rods, 8mm Rod use a 608zz Bearing, 10mm Rod use a 6900zz Bearing ( or Similar ). ... locate the collars 19 - 20mm from end of screw, this will place the threaded rod approx 8mm into the coupling assuming you...

(Updated 2015-08-20) Fixed threaded rod alignment issue Modified Adapto Z-Axis upper smooth rod holder 10mm with added threaded rod support. ... Adapto is a simple straight-forward 3D printer build and can be found at https://github.com/rotorit/Adapto...

This is a support for the Threaded Rod (8 mm) which is designed to be compatible with the Graber i3 3D Printer Clone, in order to maintain the stability and alignment, as much as possible.

Inspired by virex Z support, http://www.thingiverse.com/thing:34758, this adaptation is for people like me, that have acrylic "air 2" side panels without slots. Uses standard SKF bearing OD 22mm x 8mm ID x 11mm height 2 types ..1 one with solid...

Inspired by virex Z support, http://www.thingiverse.com/thing:34758, this adaptation is for people like me, that have acrylic "air 2" side panels without slots. Uses standard SKF bearing OD 22mm x 8mm ID x 11mm height 2 types ..1 one with solid...

customized with 3D Slash!

(Updated 2015-08-20) - Fix alignment issues for the threaded rod support) Modified Adapto Z-Axis upper smooth rod holder 10mm with added threaded rod support. ... Adapto is a simple straight-forward 3D printer build and can be found at...

(Updated 2015-08-20) Fixed threaded rod alignment issuesModified Adapto Z-Axis upper smooth rod holder 10mm with added threaded rod support. ... Adapto is a simple straight-forward 3D printer build and can be found at https://github.com/rotorit/Adapto...

Customized version of https://www.thingiverse.com/thing:774334 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=774334

Threaded rod supports for the 20L Sterilite gasket box. This design assumes 5/16"-18 rod, and fits the corresponding size nuts to hold the supports in place. ...A step drill is recommended to fit the inner support through the box wall.

I designed these Supports to work with The Adimlab 3d printer I just purchased to add some extra strength to the frame.  Included are 2 small corner brackets for the upper inside of the frame.  You will need to source the threaded rods and nuts, but...

threaded support rod axis z for Prusa i3

A nice LED STRIP support for 8 & 10 mm threaded rods & bars. ... Can be printed in a 200x200 bed diagonally.

Spool support for Threaded rod spool holder. ...Easy Press fit Threaded rod (5/16") Spool ID (2 5/16") Magic D filament spool used.

Top mounted spoolholder stand to be used in connection with thing 969358 (Wall-mount spool holder with quick release fastener) I made this bracket to fit m8 threaded rod. The thread for the rod to screw into is cut with a tap as this makes the best...

Attach your Bowden extruder system to 2 of these blocks and mount it anywhere along the Z-axis support threaded rods. Required: 4 x nuts to secure these blocks to the threaded rod. 2 x 20mm M3 screws and nuts to mount the Bowden extruder to these...

Frame support for M10 threaded rod It is installed on the upper plane of the frame and on the frontal plane of the frame. Fastened with 2 screws M10x20 and T-slot nuts. Allows to increase the rigidity of the frame, eliminates vibrations and...

(the threaded rods at the back of the X/Y bed need to be 170mm longer than the original size (About 85mm on each side of the bed). Both are printable without support. Orientation seems to be a bit off when I import from my software. Lower bracket...

This is just a quick fix since the original files didn't have a correct M12 * 1.75mm thread.

I have modified this to fit with 5/16 inch threaded rod.

I have modified this to fit with 5/16 inch threaded rod.

I have modified this to fit with 5/16 inch threaded rod.

The top Frame pieces are held to the frame with 3 x 15mm m5 bolts each and m5 nuts ( holes need to be drilled in Anet frame) I Printed the top and bottom Threaded rod Supports with Support, not sure that it was needed but it worked for me. The Main...

Just a simple 4" threaded rod

A threaded rod with metric therading . Parameters can change . ... diamete mm pitch mm kength mm Please don't forget to 'Like' the model if you download

http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: nut_type = normal head_diameter = 12 socket_depth = 3.5 slot_depth = 2 drive_diameter = 5 drive_type = socket facets = 6 nut_height = 6...

http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: nut_thread_outer_diameter = 9 head_diameter = 12 facets = 6 thread_step = 2 countersink = 2 outer_diameter = 14 thread_outer_diameter = 8...