tiny whoop nano canopy 3d models

I prefer the glow wire since they are usually not as bright as LED strips and therefore don't overexpose the FPV video feed from the whoop camera. Additionally, those are very power economical and you can use a 9V block battery to power them for an...

You can revitalize an old UDI U816 micro quad with a tiny flight controller that measures just 26mmx26mm in size, making it the perfect upgrade. The adapter is securely fastened to the U816 frame using original screws, while the controller itself is...

In addition to the time-consuming process of transferring components, I also dread moving small parts from one frame to another due to the wear and tear it causes on flight controller connections with tiny AWG wires. This redesigned 75mm frame...

Flight Controller: Visit http://www.banggood.com/Eachine-Tiny-32bits-F3-Brushed-Flight-Control-Board-Based-On-SP-RACING-F3-EVO-For-Micro-FPV-Frame-p-1087648.html?p=LD020411878172015024 to explore this option. Coreless Motors: Explore the 4X Chaoli...

For those of you who have the D8 rx version of this BNF drone, this gives you a mechanical antenna support I have also included a lengthened battery strap to allow for the GNB 660 which is slightly girthier than the original 450 1s LIPO's intended...

I'm excited to share this latest print with a 45-degree angle camera tilt. The decision to print with or without support is entirely up to your personal preference, so feel free to experiment and see which one looks better to you. ...If you need any...

BetaFPV 85x Canopy Delivers Reliable Signal Coverage to TBS Unify Pro32 Nano Air Units through its High-Gain Design.

Flywoo 1s Baby Nano 15 degree canopy with antenna mounts. Print it on its side in TPU. ...Use tree supports touching build plate.

BetaFPV's 85x Canopy - A Perfect Match for the Caddx Nebula Nano Kit The BetaFPV team has been working tirelessly to create a high-performance canopy that would pair seamlessly with the Caddx Nebula nano kit. The result is the 85x canopy, designed to...

Mobula7 cinewoop conversion. ...Adds diamond vtx and caddx ant to the mobula7 frame.

A mount fot the Hawkeye Thumb 4K

Standard 26mm mounting holes accommodate common brushless flight controllers - ESC all-in-ones, perfect for this size. Tri-motor mount features 10mm diameter hole locations to fit most popular micro motor sizes like the 0703 1500kv. The 48mm internal...

Camera Mount: Set to a Steep 28-Degree Angle of Tilt.

Features: - Lightweight (single 0.5mm wall) - 100% Camera protection - Bottom skirt to prevent dirt entering your electronic - Smooth design (no fancy fins that bricks aerodynamics)

The Diatone GTR plastic canopy has a minor issue - it's slightly too long for the Caddx Nebula nano camera, so I crafted this TPU protector that slips seamlessly over the two lips on the canopy. The lens fits snugly through the canopy lens hole,...

Modelled Canopy around Camera Mount Version 1: Modelled Canopy around Camera Mount Version 2: Canopy with Upper and Rear Protection Version 3: 2.5g - Adjustable Camera Support Clamp with 2mm Screw Version 3.1: 2.8g - Expanded Mounting Arms Protecting...

This is the canopy that I featured in this build video: https://youtu.be/YxDOrr-jt40 I designed it for the Runcam Nano HD camera, which works with Shark Byte digital FPV. It should work with most other "nano" cameras with a 14x14mm back plate. The...

Here is a modified HaloRC Odin Canopy, designed to fit the new RunCam HD Nano camera that has quite an extended lens. Includes a dipole and flipstick mount, although I used the dipole mount to hold an Axii antenna in place. ... ...

This is the canopy that I featured in this build video: https://youtu.be/YxDOrr-jt40 I designed it for the Runcam Nano HD camera, which works with Shark Byte digital FPV. It should work with most other "nano" cameras with a 14x14mm back plate. The...

... V2. It was a perfect fit except that I had to trim about 1mm of material from the front to avoid a blue tint on the sides of the FPV image. This canopy is a remix of the Pickle canopy by Alex Arvinte: https://www.thingiverse.com/thing:3499430

DEPRECATED => see my v2 instead http://www.thingiverse.com/thing:1715901 This remix of OscarLiang tiny whoop alike frame for 8.5 motors has several objectives. They are easier to print with no support, weigh less than before at 13g for the main frame...

5 Degree and 10 Degree Camera Canopies.

All available canopy models do not support a vtx mount, they are designed for only one camera (I understand that a small drone needs a flight controller with a built-in video transmitter, but I have what I have).I own 2 different cameras, these are...

My print weighs in at about .6g by far the lightest 3d printed canopy I've seen

The canopy for the main plate Chaser88 frame from Banggood (http://www.banggood.com/Eachine-Chaser88-FPV-Racer-Spare-Part-Frame-Kit-with-Aluminum-Column-Screws-p-1121633.html) is designed to protect electrical equipment, including a 4in1 6A racerstar...

Racerstar F405 WING NANO 2-Hole TINY WING 450X V2 https://paypal.me/rcpoint

This is a standard toothpick canopy with M2 mounting holes. ...A required nylon/plastic screw nut secures the canopy in place. It's designed specifically for use with the Runcam Nano 2, Racer Nano 2, and Caddx Baby Ratel FPV cameras.

Here are the specifications: A 7mm motor hole is required. The motor-to-motor distance must be under 60mm. Printed with a super light material, approximately 5g in weight - Nylon or PETG is recommended (PLA may not provide sufficient durability).

These motors come equipped with 7mm holes, allowing for motor-to-motor distances of under 60mm. The super lightweight design weighs in at just 5 grams. For optimal performance, we recommend printing these motors with nylon or PETG filament. PLA may...