tiny whoop parallel charging board 3d models
141303 3d models found related to tiny whoop parallel charging board.thingiverse
Parallel charging board for six Tiny Whoop batteries. ...Requires pin headers to be soldered in place from the underside.
thingiverse
Bottom cover for the Hobbyking parallel charging board. that came with just a layer of foam rubber to cover the bottom of the circuit board. This part just clips on, around the edges of the circuit board. ... Print with 100% infill.
thingiverse
A simple frame for the Hobby King Parallel Charging Board. I didn't like the idea of a cheap piece of foam being the only thing keeping packs from shorting against an aluminum table. ... Should work nicely with the XT60 version but I haven't tested...
thingiverse
Therefore, I designed this simple device to connect to your standard lipo charger (XT60 output) and charge up to 4x 1s lipos parallel. Please watch the video for building instructions. ... BOM: <a...
thingiverse
D.I.Y. ... -- XT-30 2S LiPo parallel Charging Board. ...
prusaprinters
<p>D.I.Y. ...-- XT-30 2S LiPo parallel Charging Board. Category: R/C Vehicles
thingiverse
http://www.banggood.com/ISDT-SC-608-150W-8A-MINI-Smart-LCD-Battery-Balance-Charger-p-1057271.html?rmmds=search http://www.banggood.com/XT60-Plug-Parallel-Charging-Board-For-ISDT-SC-608-SC-620-Charger-p-1091255.html?rmmds=search Welcome! ...Print...
thingiverse
M3x25mm=4pcs Buy: ISDT SC-608 150W 8A MINI Smart LCD Battery Balance Charger https://goo.gl/tLzMZe Parallel Charging Board Supports 5 Packs of 2-6S Lipo Battery XT60 T Plug - XT60 https://goo.gl/fNCbBS AMASS XT60 Plug Extension Wire Cable Male...
thingiverse
Printable case for CleanBoard - quality parallel charging board Thanks to creator of this case - Mariusz Taracha Check his profile: https://www.thingiverse.com/mrnx3 Buy CleanBoard: https://bit.ly/3wjRdfK FanPage: https://bit.ly/2DZ3LU6 All products:...
thingiverse
Generally, stock 1s lipos for tiny whoop are selled with JST 1.25mm connector. The Jst 1.25mm may fit with some hot glue. You also can swap your former 1.25 connector to a 2.0 of each of your lipo. The choice of 2.0mm connectors comes from the...
thingiverse
Protector for board in TPU Designed for Parallel Charging Board XT30 Plug 1S-3S Lipo Battery Upgrade Protects the cables holding with two nylon flanges...
cults3d
Protector for board in TPU Designed for Parallel Charging Board XT30 Plug 1S-3S Lipo Battery Upgrade Protects the cables holding with two nylon flanges...
thingiverse
Parallel Charging Board for 8 Batteries (4s or 6s) with Voltagedisplay.Fits balancer plugs with plastic protector well. [Nice chicks and a free slice of pizza included] Parts required: - PCB : Order at jlcpcb or similar: Simply Upload PCB_Files.zip...
thingiverse
... I was always concerned about making this mistake and i mainly only charge 4s batteries so to cap the rest of the ports off was a no brainer. I hope this help to prevent some fires and even save peoples gear. ... Files for 2s, 3s, 4s, 5s and 6s
thingiverse
Remix of https://www.thingiverse.com/thing:2740481 for conpatible with older boards like this...
thingiverse
prints with no supports. ...3 layer walls with 20% infill prints fast and strong enough. finger tight onto strips of foam board to build different gates.
thingiverse
A simple housing for a BT2.0 parallel charge board. You will need to purchase 8 BT2.0 connectors, 2 Screws, an XT60 with leads, and optionally a ziptie. I used 14awg wire, anything thicker may have a hard time fitting nicely through the opening, but...
thingiverse
Tiny whoop box for holding: - 1 tiny whoop 65mm drone. - BetaFPV charger. - up to 1s 300mah BetaFPV batteries. Holding up to 24 charged batteries and 12 empty batteries. ...
thingiverse
Ceci est une pièce pour un tiny whoop (brushed) pour passer de tiny whoop à tiny whoover ! ...(sans casser ou modifier le quadcopter, juste en ajoutant deux pièces) Non adaptée pour tiny whoop en moteur brushless.
cults3d
This is a piece for a tiny whoop (brushed) to go from tiny whoop to tiny whoover! ...(without breaking or modifying the quadcopter, just by adding two parts) Not suitable for tiny whoop with brushless motor.
cults3d
Ceci est une pièce pour un tiny whoop (brushed) pour passer de tiny whoop à tiny whoover ! ...(sans casser ou modifier le quadcopter, juste en ajoutant deux pièces) Non adaptée pour tiny whoop en moteur brushless.
thingiverse
This is a Tiny Whoop frame that I made for the BeeCore V2: https://goo.gl/jnnfmk Designed to be printed in Nylon, but should work in other filaments just fine. ... Should fine any standard tiny whoop board and props.
thingiverse
Super simple little base to help press tiny whoop style motors into tiny whoop style frames.