titan aero anet a8 3d models

Print Settings Printer: Anet A2 Rafts: No Supports: Yes Resolution: 0.2 Infill: 50% Notes: Printed with 4 walls, and a 50% grid infill, which honestly, there's not a lot of on this model, making it a very strong but plastic conservative print. Clean...

Print Settings Printer: Anet A6 Rafts: No Supports: No Resolution: 0.2 mm Infill: 20% Grid Notes: Printed with a retraction setting of 1.5 mm using black WYZ Works PLA filament, 1.6 mm wall thickness, 200 C extruder temperature, and 50 C heated bed...

If the material deforms or softens it will no longer hold on the arm as it is upside down and will fall. Print Settings Printer Brand: Anet Printer: A4 Rafts: No Supports: No Resolution: 0.15 Infill: 25 Filament: Generic PLA PLA Black Notes: PLA...

:D\nPrint Settings\nPrinter: \n Anet A6\n \n Rafts: \n Doesn't Matter\n \n Supports: \n Yes\n \n Resolution: \n 0.20\n \n Infill: \n 25%\n\nHow I Designed This Case\nA friend of mine took the initiative to measure all the dimensions first, then...

here are the complete kick panels, as well as sliced into 3 smaller sections to print on my anet printer. I purposefully left out the mounting holes as I was exploring different mounting ideas. For now, I just heated up a metal tool of sorts to...

The design intends to utilize the standard Anet spool holder shaft and the original kit's provided nuts and washers. A 35mm long (40mm deep blind hole in the model) M8 threaded bar is screwed into the mount's threaded hole, followed by a lock nut and...

I designed this to fit behind my Anet 8 in a lack enclosure. I wanted a removable top, and also wanted to mount my electronics underneath in the a spirit of the new Vorons. A drop down skirt is in the works. I used this bread board. ...

... one is very fine , 50 microns (0.05), one is 0.10 and the last one is 0.2. I had placed a stl model but a lot of people had problems to print it. I had to use special retraction parameters to avoid bumps. I tested it on a mecreator2 and a anet 12.

Alternatively, you can use a zip-tie (I have plenty that came with my Anet printer) and if you drape it around the part when installing, you can reach it from above to tighten it. To be honest, I'm not a skilled photographer... If I manage to take...

He puesto otros grosores para que se pueda hacer al gusto. Print instructionsCategory: Tools Print Settings Printer: Anet E10 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.3 Infill: 50% Notes: Yo las he impreso al 50% y 100% para...

I use an Anet A6 so i put my slicing's seting. The case is consists in two part: the first one is the body of the case, i printed it in TPU. The second part is insert il PLA. (All setting are based on my 3d printer, an cartesian 3d printer) ...

... Print Settings: Printer Brand: RepRap Printer: Anet A6 Prusa Rafts: Irrelevant Supports: No Resolution: 0.5 Infill: 15% Notes: "4_out_cap_with_tube.stl" is designed for simplified printing, so you'll need to assemble the parts by applying ABS glue.

They all fit perfectly and the box can be turned upside-down. I used https://www.thingiverse.com/thing:2027087 to create STLs. I also added a tray for longer tools. Print Settings Printer: Anet E10 Rafts: NoSupports: No Resolution: .3Infill: 25%...

This is a quick remix of TomExplorador's (LESS PARTS!) Frame Braces Titian & Creality CR-10 & ANET). I personally use it on my **Tevo Tornado** but since I didn't change the dimensions, it should fit **CR-10** etc. as mentioned in the original...

... The rod diameter is 8mm. The following rod lengths are needed; 113,7mm (4x); 81.6mm (2x); 35.3mm (2x).] Print Settings Printer Brand: Anet Printer: A6Rafts: No Supports: NoResolution: 0.2 Infill: 40% Filament: eSun PLA Category: Household

I designed it in TinkerCad, and sliced it in Cura 4.8.0 using the ANET E10 profile. I modified temp settings as indicated for the PETG. I printed a normal setting (.15) but with 100% infill for strength. I printed with a brim just because the...

... ball bearing for distance.</p> <p>Ball bearing is used. 5mm thick, 5mm axis, 11mm outside diameter. Print Settings Printer Brand: Anet Printer: A6Rafts: Doesn't Matter Supports: Doesn't MatterResolution: 0,3 Infill: 20% Category: R/C Vehicles

... grams when printed correctly. See setup below. Print Settings Printer: ANET A-8 Rafts: No Supports: No Resolution: .2mm Infill: None Notes: Use two walls, zero infill, 2 layers bottom, 3 layers top for lightest weight. Category: R/C Vehicles

Design: FreeCAD 0.16 Slicing Software: Cura 3.0.4 Printing Details: Anet A6 printer in PLA with a 0.15mm layer height, 15% 'zig-zag' infill, 0.8mm shell, and 0.45mm top and bottom layers. One skirt was printed to prime and clear the extruder of...

P's: Red Reinhardt model printed by lsmallsl Print Settings: Printer Brand: RepRap Printer: Anet A6 Prusa Rafts: Doesn't Matter Supports: Yes Resolution: 0.5 Infill: 25% Notes: In models, no XY shrinkage compensation is applied, please remember this...

The Anet AM8 is one of many printers that can host these mounts. Thanks to [sheffdog](https://www.thingiverse.com/sheffdog) for "Linear Rail Slot Covers - Hide your wires!", I borrowed a snap-on mechanics perfectly dimensioned for the ALU extrusion...

You can buy Amazon-Anet Lead Screw Rod and nut, 345mm 8mm, on Amazon. The factory ships with 5mm rods. This custom design fits 8mm rods and sets them 17mm apart. Simply replace the rods and the X-carriage from the factory with the ones linked here...

To validate its performance, I required an attractive model that wouldn't push my little Anet A6 to the limit, so it wasn't long before the idea struck me to 3D print a hand grenade. After conducting an exhaustive search of the internet, I couldn't...

... with a drop of super glue. Chain has 8 links between the numbers and sprocket used has 32 teeth. Print Settings Printer Brand: Anet Printer: A8Rafts: No Supports: YesResolution: 0.2 Infill: 26 Filament: Das filament PETG Burnt bronze Category: DIY

PRINT SENTINGS Printed on Anet A6 at: *All measurements are in Celcius and Milimeters and can be seen on one of the images above. YOU MUST TURN 90 º THE CONTROL HORN ON ITS BOTTOM WHEN PRINTING, SO THE FLAT SIDE IS TOUCHING THE PRINTING PLATE. ...

... 360 file so you can make adjustments accordingly. Print and use with love. Print Settings Printer Brand: Anet Printer: A8Rafts: Doesn't Matter Supports: Doesn't MatterResolution: 200 Infill: 20 Filament: Porima PLA Blue Category: Organization

I was inspired by the concept of the door with hinges, but struggled to find one that could accommodate the Anet board. To fit an extra mosfet for the heatbed, it's slightly larger than the original design. You'll need 8 M3x10 screws and their...

This is a Thermometer box connect frame slider by magnet I design this so everyone can using magnet to bring or connect to every location on the frame of the 3d printer machine Print Settings Printer Brand: Anet Printer: A4Rafts: Doesn't Matter...

... slightly, though this minor imperfection doesn't affect its overall performance. I'm thrilled with the result and hope you will be too. Print Settings Printer: Anet A6 Rafts: No Supports: Yes Resolution: 0.1 Layer height, 0.3 nozzle Infill: 20%

REMIX-Pwncnc-V5-Boot -Remixed to have lip on bush plate (attempt to avoid lateral movement) -Remixed to use these magnets:https://www.amazon.com/gp/product/B07C6CYPLR/ -Remixed brush plate to have deeper channel for brush Printed on Anet ET4 -...