tomtom 3d models

I've noticed a issue on el7, where turning on the GPS can cause it to disconnect. I fixed this problem on el8. The hole for the lock is designed specifically for the lock shown in the photo with its measurements. The V16 version has been printed in...

Mount Diameter: 30mm Screw Sizes: 1x M5 x 40mm for the main mount 2x M5 x 33mm

TOM TOM Rider MT09 cover

I designed this solution specifically to complement my friend's Vauxhall Mokka perfectly without any annoying suction cups or cluttered wiring on display. Unlike manufacturers like Vauxhall who charge exorbitant fees for updating satnavs on their...

This is double color rain cap for Rider mount. Basic black color - PETg, fingers - PLA. ... Don't use a fan.

Copri Contatto TomTom Rider Serie 400-500 Logo Moto Guzzi

Copricontatti per TomTom Rider Serie 400-500 Personalizzato Moto Guzzi

A mount that adapts the TomTom GO 720 730 920 930 520 530, to fit on the iOttie Easy One Touch 4, holds on very securely.

A mount that adapts the TomTom GO 720 730 920 930 520 530, to fit on the iOttie Easy One Touch 4, holds on very securely.

This is a mount for the TomTom Rider 550 GPS on a 12mm GPS bar (like on the Tenere 700). The hole pattern in the mount is exactly the same as the hole pattern on the GPS. ... Pro tip: Use thin double sided tape between the mount and the bar.

Clips onto the back of the following tomtom models: START 42, START 52, START 62, VIA 52, VIA 53, VIA 62 The model obviously just provides 4 screw holes and not a ball mount, this is because you also need to print this model...

To achieve this, I created a three-piece assembly that integrates a ball/socket mechanism, allowing effortless rotation of the TomTom unit and the cupholder clip, which enables smooth sliding of the cradle along the edge of the cup holder. Eight...

... 30% Filament: eSun ABS+ Black Notes: Should be printed in ABS if in hot climates, possibly PETG in a pinch. ...Sanding may be needed for the inner circle, mount should only be able to release once you press the TomTom button latch. Category: Gadgets

... mm * Infill: 100% This mount was printed with clear resin and required 60 minutes of UV hardening to cure. To assemble the custom mount, you'll need: * The original TomTom Rider Mount * Screws from the original mount * 4x M4x35 screws * 4x M4 nuts

Primer cal fixar el suport TomTom a la base del suport imprès amb cargols Allen i les seves corresponents volanderes i femelles; tenint en compte la posició de la ranura por on sortirà el cable d'alimentació. Després, cal posar la tanca per la part...

My trusty old Tomtom One V1 suction cup holder finally gave out. Breaking open the broken piece wasn't a straightforward job, but after extracting the offending axle, I swapped in a brand new 3D printed ABS component. ...A word of caution - don't rush...

This is a custom-made bracket for TomTom Go 520 or 620 owners who want to adapt their device to an existing vent mount or other setup. To create this bracket, simply glue the 3D printed piece onto an old vent mount you have lying around - I used mine...

iphone 6 plus mount on the tomtom plug for fiat - sostegno per iphone 6 plus su mix di 2 elementi trovati su thingiverse, aggiunto anche un secondo supporto con sistema di bloccaggio, anch'esso adattato.

To ensure you're getting the most out of your TomTom GO 6000, customize your map display by going to Settings > Map Display. Adjust the settings as needed to suit your preferences for road types, traffic information, and more. Finally, before...

iPhone 6 Plus mounts on TomTom plug for Fiat using a custom mount made from two Thingiverse-designed components. The additional support system was created to provide added stability and security. ...Printing settings include rafts that can be turned...

The rotating base for the TomTom Rider mount is a bit thick so I made a part that replaces the rotation part with a slimmer piece that has holes for CNCKitchens heat-set thread inserts.And also a piece that mates with the release-lever on the rider...

This is a custom holder designed specifically for GPS devices of the TomTom 600 and 6000 series. The base is cleverly crafted to fit snugly between the car radio and upper vents, and is angled at 30 degrees to match the casing's slanted design. To...

I'm not a perfectionist, but this does the trick for me. The file includes a security band lock that I didn't bother printing out. It's designed to be printed on the reverse side, showcasing its sleek face. It looks fantastic. I printed it with a...

Needed a Mounting Bracket for a Top-Notch GPS Device. Parts List: 2 x M4 Bolt and Nut Assemblies. ... Thanks to the contributor who shared the design for this mounting hardware: https://www.thingiverse.com/thing:641854.

Imprimé sur ma creality ender 3

I needed a housing for an excellent GPS unit, an older model. ...Here's what I came up with: Parts list: 2 x M4 bolts and nuts

Print Settings Printer: Custom Delta Rafts: No Supports: Yes Resolution: 0.2 Infill: 20%

Join the Multistrada revolution on a Ducati ball.

I upgraded the MSHax mount to work seamlessly with my motorcycle by adding a rugged RAM ball, ensuring a secure and stable connection for all my adventures on two wheels.

Attach a conveniently detachable plate using Velcro to your dashboard, and securely fasten your GPS device on it for effortless accessibility and swift detachment.