water bottle hose adapter 3d models
229018 3d models found related to water bottle hose adapter.thingiverse
This design allows to connect 6mm(inner diameter) hose to 5l or bigger water bottle.This adapter is air tight i used this in my compressor (2atm) to attach bottle as expansion tank. To instal this adapter you need to drill 10mm hole in center of the...
thingiverse
On the other end i want connect intex hoses(38mm).(see picture) The goal was to maximize the water flow and i dont want to use all these bad fitting adapters anymore. The only thing you have to buy is sealing rings ~52mm outside diameter. I reused...
prusaprinters
I was asked to make a parametric water adapter, here is it. Category: Replacement Parts
thingiverse
Needed for a water pump that did not come with the adapter. ...it works well with no leaks
thingiverse
no much to say, a part that frequently gets damaged in cheap water taps. Remember saving the ribbon ring, it goes like in the pictures. ... Remember printing it in a higher temp material like ABS!
myminifactory
Water your plants with this water bottle adapter that fits onto any standard plastic bottle.
thingiverse
... was riding, regardless as to how tight the Velcro straps were. ...So, I designed an adapter that attaches to the frame and allows the water bottle holder to bolt to it and prevent it from rotating. ...Will fit any oval bike frame measuring 55 x 33.5mm.
thingiverse
My Nalgen brand water bottle (pictured) is too big for my 'standard' sized cupholder, so I made this adapter. The bottom part still continues to support most "normal" sized cups/water bottles. Hope you find it useful... and yes, I know I can...
thingiverse
Adapts 1/2 NPT to "soda bottle" threads like a 2 liter bottle has. This object is a remix (combination) of 1/2" .5" NPT plug (http://www.thingiverse.com/thing:210455) and thread creation exercise (http://www.thingiverse.com/thing:333670). It prints...
thingiverse
This allows most 16.9 oz bottled water to fit in your Yeti can cooler. (old style, not the newer 1/4 turn cap). ... Created with TinkerCad
thingiverse
Small ring with inside threads to fit small disposable water bottles that have the very short cap. The intent is to provide a minimal piece that can be worked into other designs. This was specifically designed off of a Crystal Geyser bottle. The...
cults3d
After looking around for 3D printed weights, I decided to work with what I had lying around, and designed this clip for a 1.5L water bottle (athough it would probably fit other sizes). The ring is designed to slide on a 2" barbell. If I had more...
thingiverse
After looking around for 3D printed weights, I decided to work with what I had lying around, and designed this clip for a 1.5L water bottle (athough it would probably fit other sizes). The ring is designed to slide on a 2" barbell. If I had more...
prusaprinters
Water hose adapter with a 1/2" thread Print instructionsLicence: Creative Commons - Attribution Category: Parts Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution: 0.1 Infill: 50%
thingiverse
Turn those discarded water bottles into a watering bulbs !
thingiverse
Replacement wide mouth bottle adapter to connect a Katadyn water filter to Nalgene type bottles.
thingiverse
This is a remix from https://www.thingiverse.com/thing:3309461 using the hose adapter from https://www.thingiverse.com/thing:2735925. The hose adapter was resized from original 14mm to 11mm. ...
thingiverse
BJPKPK 64OZ Water Bottle Adapter for use with a Rotary Engraving.
thingiverse
This is an adapter to make a yeti water 28 oz water bottle fit in a standard cupholder in a car.
thingiverse
Bidet water bottle adapter V3 After the print, take a lighter or hot water to the threads to loosen them before screwing it on. The threads are rather tight. ...Also clear the nozzle hole.
thingiverse
The hole for it to thread into is 0.54" diameter with a thread pitch of 0.05556" (18 threads per inch) After printing, apply teflon tape to both the bottle threads and the 1/4" NPT quick disconnect before screwing into the adapter. I screwed it...
thingiverse
For use on a cup tumbler turner for applying epoxy. ... Screws directly into the 20oz Tal water bottle. ... For use with 3/4 inch pvc pipe.
thingiverse
This fitting allows a cut off water bottle to be fixed to the stiff tube part of my aquarium gravel cleaner. ... The threaded part can be found here - https://www.thingiverse.com/thing:5238061
thingiverse
Water bottle cap for Bottle Monsters. ...Works on most 500ml water bottles. Source for water bottle threads: https://www.thingiverse.com/thing:4745228 Printing: Cura defaults. ...(20% infill, 2 walls, no supports, no raft or brim needed)
prusaprinters
Rotate the upper piece until it falls into place. Place the assembled adapter into the desired cupholder.Finally, tighten the screw into the fastener through the upper piece. This will lock the top and bottom pieces together, and extend the...
thingiverse
Needs 2 a small 3.5diax15mm wood screws and 1 spring from a pen. ... locks into the Fabric cageless waterbottle pins strap around your normal water bottle with zip ties
thingiverse
Pop, soda or water bottle to male garden hose adapter. To connect a water bottle to a garden hose or other plumbing. ...Use a garden hose washer to seal the water bottle connection.