top 3d print files

This quad suffers from the same issues as other similar designs: The printed parts are not robust enough and will likely crack due to vibrations. After some time, the part will resemble shattered security glass with numerous cracks. To assemble this...

I printed this part from clear PETG on my Anet A8 with a 0.5mm nozzle. Although I am still fine-tuning the settings for PETG, the part fits nicely under the motor mount after some adjustments. To assemble this cover, you will need six M3x8 screws,...

This part prints in two pieces, with the first piece being likely smaller than the spur gear. You can compress the rear half of the cover to clear your spur gear (one side at a time) or remove the spur gear and attach the first half of the cover...

... model, iPhone versions and so on. ... Note that values above 58.5 for certain parts resulted into no actual increase while maintaining the aspect ratio so their names were given but not taken by any effect to this object when printed on Maker Bot.

When I do this, I will create a detailed video that covers all the steps from printing to installation of the gear. This way, I can showcase what the gear looks like when it's freshly installed on the plane, not after it has been dragged through the...

I designed these to work using ESP8266 (ESP-01 modules) and three WS2811 RGB LED pixels with a custom printed circuit board (PCB) that can be made with a breadboard using the schematic. The ESP-01 module is running forkineye firmware(forkineye.com)...

Thingiverse Apps URL: http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: Music Cylinder Name: test song Print Flag: Yes (1) Gear Holding Radius: 4 units Case Generation Flag: Yes (1) Debug Gears...

With some base textures the difference is negligible (between the 25mm ones) if the texture doesn't have much definition, but I've included them for the odd chance that is exactly what someone needs.It's probably best to print these with a resin...

The most important thing is to choose a fabric with a subtle print that complements the doll's image. Since these dolls are usually made in compact sizes, it's best to use fabrics with smaller patterns. Tilda dolls can be created using two different...

*Print from some flex material, Fillamentum 92 - 98A or something.* How to install: - Start your vehicle and raise it. Wait until your air pump will run out. - Open driver's door. - Turn engine off. Keep the door open during the whole proces! -...

Print settings have been configured for monochrome output using the primary extruder. Secondary extruder used for text is set as extruder2. Outline color is displayed as Gray. Glyph coalescence has been limited to 25 units. Inner margin width has...

Print this out flat, without any supports, and add a 1/4" X 3.5" long nut and bolt to complete the job. If you're wondering about that undercut on the tool, it's there so the gauge slides over hammer strikes on the edge of the Bowen nut - preventing...

Print Settings Printer: Monoprice Maker Select Rafts: No Supports: No Resolution: 0.15mm Infill: 15% Video MPLABX PIC C Code #pragma config FOSC = INTOSCIO //Internal oscillator - I/O on RA6 and RA7 #pragma config WDTE = OFF //Watchdog timer off...

Post-printing, connect a length of wire to the negative base of the battery and form a ring around the threads. Be sure to circumnavigate the battery in a counter-clockwise direction so that as you screw on the electronics enclosure, the wire isn't...

After gluing you will not be able to remove the magnets.  All parts are chamfered so elephants feet will not get in the way, The rear side of the drawers are filleted as well to make it somewhat easier to insert the drawersI printed the parts in PLA...

It should allow some movement inside the bit (if not, just print at larger size). Use two attachment points, cut at different lengths, to tilt the sashimono forward or backwards. Not the most elegant solution, but it should work! Personalized...

Basic "I don't want my protoboard shorting or gouging holes in my desk" feet/standoffs for M3-drilled 1.6 mm thick PCBs. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 mm Infill: 15% Filament: Eco Tough...

I printed the pictured version in PLA but plan to reprint it in PETG for increased longevity. I used specific hardware to allow the interlock to slide back and forth. A spacer: #6 ID X 1/4 inch OD X 1/4 inch L, aluminum was used. The product can...

Additional set for RS-CNC: https://www.thingiverse.com/thing:3010914 These are the parts I drew to accomplish: - Remove electronics from inside of RS-CNC - Make two original parts stronger 1) Facade Addon - Add a switch for light on/off - Add a...

This model is not finished, but the main parts are suitable for printing and assembly, I could not figure out the arduino to finish the assembly. I don't have the funds to finish the project, so I'm posting it here in the hope that someone will find...

... (2018.10.13) - Added better pictures. - (2018.11.13) - Added Derivative Works Policy. - (2018.12.13) - Re-uploaded the models in proper print orientation. - Derivative works now fully allowed! - Merry Christmas! .../ Happy Holiday Season!

This adapter plate simply slides onto the back of the Parrot 2 Teleprompter, you need to print out the generic 1/4" x 20 tripod plate below to stick on the bottom of the teleprompter in order to mount it on any tripod with a standard screw mount. I...

I printed mine using MakerGeeks PETG, but next time, I'll probably use PLA and then subject it to 80C for 40 minutes. Unfortunately, PETG didn't hold up as well as I had hoped under high temperatures. In addition to this jig setup, here are my...

The straps are printed in TPU for better flexibility when opening and closing. This also ensures that they do not interfere with the movement of the plier during use. The clamp remains fixed by one side on one of the two handles in use to be...

The original duct is unsuitable in places to print larger overhangs cleanly. This model is the result of a very long series of tests as a joint project and provides excellent results. The test series was tested by 2 diligent supporters, independently...

The SKR v1.3 board mounts with M3 screws directly into the printed plastic. The holes are 2.8mm diameter, so the M3 screws will cut threads into the plastic if you turn slowly with pressure at first. This works best with PETG but also works with...

You can view it here: https://www.thingiverse.com/thing:3137474 For best results, print at 0.1mm - 0.15mm layer height and supports for the bottom. This design will fit any Whoop style frame as long as the mounting holes are standard Whoop style, but...

On the one hand, the heat from the stepper motor and the print bed does the connector no good. On the other hand, the movement is another reason for the frequent contact problems, up to the burning of the connection. I took the hints already given...

The creator recommended not using PLA, however I've printed two complete cases using ToughPLA and have had no issues with warping at all. Unit has been working as a 24/7 Plex server for multiple users for almost a year and is almost always in use...

Simple Waveshare 7.5 NFC E-Paper holder for Kegland Kegerator or if you use the Kegland Quadruple Tap Font. The original Waveshare case is no used. screw used: M3x10mm Screen used : https://www.waveshare.com/wiki/7.5inch\_NFC-Powered\_e-Paper...