traxxas jato 3d models

This is a trailing rear arm configuration of Traxxas Jato 3.3 model. ...The project was based on using 3D printed parts of PLA (Flexible parts) and ABS (Rigid Parts) filament.

Traxxas Jet receiver box cover, The part can still be improved, SolidWorks file included Oficina do Automodelo - Brazil

A co-worker has a Traxxas JATO 3.3 radio controlled race car. He broke one of the struts and has ideas to make a custom setup. I worked with him for about an hour to sketch this up. It hasn't been printed yet but looks promising. Notice the "JC" for...

See my Jato here at 26s : https://youtu.be/2eAbIpnACgw?t=26 Print setting : Print the motor mount in ABS ! I tried with PLA but the engine becoming too hot made it to melt a little after ~5-6 runs. But you can use PLA if you want and if your motor...

Skis to use in the snow when it hits! Skis will mount to 30 degree caster block in place of the steering block. Steering linkage connects just like it would with the steering block. Instructions Only...

This is a wing for the original holes on the body.

Have fun and add whatever you want or keep it blank. ...This fixes the corner printing all weird.

End Update This is a brushless conversion kit for the Traxxas Jato. The battery box is 43mm * 135mm. I used two of these batteries in parallel: http://www.hobbyking.com/hobbyking/store/__11949__Turnigy_nano_tech_3300mah_3S_35_70C_Lipo_Pack.html The...

Drone a Jato.

Começando a fazer modelos 3d no blender

No description provided.

This is just the small linkage peice of the sway bar on a Traxxas Jato 3.3. This part seemed to break often for me and to replace a whole sway bar kit must be purchased. ... Instructions There is two...

This is a Jato Conversion with my spin on it. I have always loved the Jato. Just don't care for Nitro anymore. I used https://www.thingiverse.com/thing:1581048 motor mount. And design the rest. All you need to complete this build a few extra 3mm...

Traxxas Jato 3.3 tire design

AVIÃO JATO F16 FALCON MODELADO EM SOLIDWORKS 2012

AVIÃO JATO TORNADO GR4 , QUE FOI MODELADO POR OUTRO ENGENHEIRO , EU TINHA ESSE ARQUIVO GUARDADO HA MUITO TEMPO , E AÍ RESOLVI POSTAR ESSE TRABALHO MARAVILHOSO.

Mesa jato e Suporte do Data

Front Bumper for Traxxis Jato 3.3

ESTRUTURAL LAVA JATO AQR BY ELU ENGENHARIA

Its not exactly like the one you'll order from Traxxas but I would go out on a limb and say its stronger than their part. (their way of making extra money). I went out and tested it in the parking lot and hit a light pole and it impacted on the...

Thanks to <a href="Renato Lunardini Júnior" target="_blank">Renato Lunardini Júnior</a> for this awesome model <a href="AVIÃO JATO TORNADO GR4" target="_blank">AviÃo jato tornado gr4</a> All my entries here:...

Motor a Jato modelado de acordo com blueprints(MW 54 Turbo Jet Engine) que encontrei na internet... ...Dizem que é funcional...

traxxas bulkhead part 2530

traxxas 6845x parts

No description provided.

Adaptação de container

Traxxas SKI fits 12mm hex

forgot what number this was but needed to model one into the jato to figure out spacing for braket

this Traxxas logo was made on inventor

A coaster with the Traxxas emblem. ... Enjoy!