traxxas slash 2wd brushless motor upgrade 3d models

Burnout bar to use on a Traxxas Slash based No Prep car. Fits a standard RPM style Wheelie bar mount and depending on your body, should be completely hidden underneath. I used this mount and designed this Burnout Bar to fit it perfectly.

RC Stand for Traxxas Slash 4x4. Included are both HCG & LCG Chassis Stands. HCG is still a work in progress. LCG is complete and the bay has room for the Traxxas EZ Peak+ ID Charger. Support are required for the front opening. Supports for...

... configurations. The updated design boasts sleek lines and a rugged build that perfectly complements the Slash's aggressive stance, making it a testament to Traxxas' commitment to delivering high-performance products that exceed driver expectations.

Here's a quick and simple mount I came up with so I could run Jato rear shocks on my Slash without sacrificing ground clearance. I mounted my body mount on the front side of the shock tower, so make sure to factor that in when building yours - this...

... using way less time and fillement than making a whole tire, I did try making a full tire but i quickly snapped off the hex. ...This should work on 2wd and four wheel drive slash. ...If you cant get them on try using a bit of sand paper on the inside.

EDIT: updated with newer design a rear bumper for the 1/10 scale traxxas slash use with my printable bumper arm http://www.thingiverse.com/thing:1175688 and printable bumper arm brace for extra support http://www.thingiverse.com/thing:1175687 Print...

the 2 holes in the middle of the part are for attaching an additional center brace for extra support. use with my printable bumper http://www.thingiverse.com/thing:1175690 use with my printable bumper arm brace for extra support...

Here are some 3D modeling creations I did for the Traxxas Slash. Each part has been thoroughly tested and pushed to its limits on several Slash models. Some components perform exceptionally well in specific materials, such as nylon, which is ideal...

Traxxas Slash Lowering Kit using stock Suspension. You will need 4 standard slash screws. (can buy off of amazon or use old screws) It reduces front suspension travel and the rear is just lower. Perfect for drag racing or undersized bodies...

the lower shock spring support for the suspension on the 1/10 scale traxxas slash. version with shield http://www.thingiverse.com/thing:1175692 Print instructionsUnassociated tags: r/c Category: R/C Vehicles

The Traxxas Slash battery cover is a vital component that requires attention to detail and precision craftsmanship. ...The sleek design of this cover not only adds an aesthetic touch but also provides protection from the elements, ensuring your...

Updated design now available featuring a rear bumper specifically designed for the 1/10 scale Traxxas Slash. This bumper is intended to be used in conjunction with my printable bumper arm, which can be found at Thingiverse under the ID number...

it has the normal mounting holes in the front for the shock, but it also has mounting holes in the rear so you can mount another shock to the rear of the a-arm (for the rear a-arms only, steering gets in the way on the front) using my printable...

This is an essential part of the Traxxas Slash's wheels system. The hub cap securely connects to the bolts that keep the wheel in place. Currently, you need to use a screwdriver to carefully pry off the hub cap. I plan to make improvements to this...

These are custom shields designed to fit onto the rear shocks of a Traxxas Slash, preventing dirt from accumulating and clogging the shock absorbers. A newer version, known as ShockGuardV2.stl, is available for use, which is recommended over the...

Updated with a fresh design, this is a rear bumper tailored specifically to the 1/10 scale Traxxas Slash. For optimal stability and alignment, it's highly recommended that you use it in conjunction with my printable Bumper Arm, available on...

Here's an updated look for your Traxxas Slash, just a little something to give it some personality. You will find all of the assembly details below: First off, fire up your printer and hit print on both pieces with 100% infill - don't worry about...

This is the updated design for the 1/10 scale 4x4 Traxxas Slash's A-Arm. It features standard mounting holes in the front for shock installation, as well as additional holes at the rear to accommodate a secondary shock mounted using my printable...

This is the a-arm for the 1/10 scale 4x4 Traxxas Slash. It features standard mounting holes at the front to secure the shock, but it also includes additional holes at the rear, allowing you to attach another shock to the back of the a-arm...

Updated with New Design This A-Arm Works Perfectly for the 1/10 Scale 4x4 Traxxas Slash Vehicle. It Includes Normal Mounting Holes at the Front for the Shock Absorbers and Extra Holes at the Rear to Attach Another Shock Absorber. The Mounting Holes...

I've been converting a long-running project to a 2WD Slash for months now. Unable to find an Rx box from local sources, I decided to design and print my own. It bolts down on stock mount holes and holds any Rx unit imaginable. A holder for the...

I've been converting a long running project to a 2WD Slash for the last few months. Couldn't find the Rx box from any local sources, so I decided to design and print my own. It bolts down on the stock mount holes, and holds any Rx I can think of. It...

This mount/bracket allows you to keep the entire antenna mounted under the body of the slash. It just clips on to the chassis. It also has an eyelet that allows for you to attach a tether to the battery retainer clip. It is best to print upside down....

Brushless Motor Upgrade Kit.

This modification fits my Slash perfectly, although the holes are slightly undersized once printed in PLA and required a bit of reaming with a round file to match the design's oversized specifications. I left some space for inserting the C-clip, but...

Traxxas Slash Alternator - The Ultimate Off-Road Buggy Upgrade

I had to reorganize the layout when I installed the Mamba Monster motor and ESC, and ran 6S for speed runs. Now that I've completed the speed runs, I needed to create a more conventional setup. Thanks to the large ESC provided by Mamba, this meant...

... variant with an optimized thickness of 1.6mm, significantly reduced from the original 2mm used in v2. Revisited the title, highlighting its purpose as an upgrade tailored for the WL Toys V912 RC heli to be powered by brushless motor technology.

Upgrades for the Traxxas Slash 1/10 Scale 4x4 Electric RC Car Bumper Mounts

From El Cheapo labs I have made this tube reinforcement for my low budget Slash Drag car. This will also fit other Traxxas models using the same axle. This is one of many economy parts that I will be releasing. Anyone can go cash bomb a rig, let's...