traxxas slash 2wd roll cage 3d models
50309 3d models found related to traxxas slash 2wd roll cage.thingiverse
Roll cage I designed for the Slash 4x4. I designed it to mount to the holes used to attach the body mounts to the truck. I have only printed this once with Hatchbox Blue PLA. I have not thrashed it yet. I expect it to break as I used PLA. I...
thingiverse
simple 2-part roll cage for Killerbody RC car body for y traxxas slash 4x4 need to be glued together and to be mounted with 4 small screws to the body
thingiverse
Printed for a Traxxas Slash 2wd. (The 4x4 setup is different) This one doesn't use bushings or bearings, so it might wear out quickly. Seems to hold up pretty well though. Thanks, Enjoy! ...
thingiverse
I adjusted the size to fit a 2wd Slash. The fit might be a little tight, but over time, it will break in. ...Fill at 100% to ensure strength.
thingiverse
All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm...
cults3d
All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm screws....
thingiverse
I have not printed this yet. Please post a make if you print it. ... Assembly with M3 screws.
thingiverse
This is a simple flat ESC Mount that fits in the stock ESC location on the stock Traxxas Slash 2WD Chassis and the LCG Chassis. It might fit other models that use the XL-5 ESC because that's what these holes line up with. The plate is 55mm x 55mm. I...
thingiverse
This is an experiment to extend the wheelbase of a Traxxas Slash 2WD to fit Arrma Infraction or Felony bodies. It makes the wheelbase 76 millimeters (3 inches) longer than stock. It is designed around the Slash LCG chassis, and I have no idea if it...
thingiverse
This is a simple wheelie bar I designed for my Traxxas Slash 2wd VXL, as it was spending far too much time on it's roof! In addition to the printed parts you will need the following parts - 2x 625 bearings 2x M5x20 countersunk head bolts 2x...
thingiverse
This is the first of many print sets for a 2wd Slash down-force system. Suitable for both drift and drag cars. When the whole system is installed your car should pull itself down and make the car squat as speed increases. This fits with and without...
thingiverse
Traxxas SLASH RC truck roll bars. These are cosmetic and really improves the look of the truck. ...I fastened them to the body by drilling holes and using little screws.
thingiverse
traxxas slash 2wd rear bumper mount compatible with asciencepotato's 4wd bumper. ...It's a little fragile, so please drive carefully.
pinshape
This is a Traxxas Slash 2wd LCG Chassis - Sidewinder SCT ESC Holder Bracket and FS-RG3E Receiver Holder. The Castle Sidewinder 3 SCT with phan will need 2 - 3x25mm to hold it in place. ... The FLYSKY FS-RG3E will need one 3x12mm and a little shoe...
thingiverse
This is designed for a traxxas slash 2wd it allows you to mount the transmission backwards for better centre of gravity and cornering ability but you can also mount it stock. ...this was designed to be cut out of aluminium but can also be laser cut out...
thingiverse
I designed these mud guards for a Traxxas Slash 2wd High center of gravity chassis to keep the dirt out of the chassis. It uses the holes from the nerf bars so you will need 4 screws that are a bit longer to replace the ones from the nerf bars. ... ...
pinshape
This is the Front Caster Block for a Traxxas Slash 2WD, Bandit or Rusler. Print them if you break one... PLA Holds up ok in mid Temp and Cold. I PLA is fine for normal racing conditions. I raced for 1 hour accident free with oit breakage. They...
cults3d
Maybe it can fit on the other 2wd Traxxas as well with some modifications. It is based on the new style of clip on straps presented on the Traxxas 4TEC 2.0 and TRX4. The only modification required to the car is enlarging the hole where the hexagonal...
thingiverse
Maybe it can fit on the other 2wd Traxxas as well with some modifications. It is based on the new style of clip on straps presented on the Traxxas 4TEC 2.0 and TRX4. The only modification required to the car is enlarging the hole where the hexagonal...
thingiverse
Body Mount Extension as Add-On to the original Body Mount of the Slash 2WD to fit the Proline F150 1979 body in the front. ... Built with Tinkercad.
cults3d
wheelie bar for traxxas drag slash use m3x16mm screws these could be used for show or as templates to fit bodies
thingiverse
This is a very simple chassis saver I designed for my Traxxas Slash 2wd with High Centre of Gravity chassis. Proline used to make these a few years ago to eliminate the weak spot where the transmission bolts to the chassis. Unfortunately, when...
thingiverse
I made this 0 degree bulkhead to make my slash into a drag car. Works great! ...Print flat with supports touching buildplate for best results!
cults3d
a roll cage for the traxxas trx4 sport, i tested it and it's verry strong (tumbled many times of a hill and did not break. simple and strong. There are 2mm holes in the mounting points. i used 2.5mm screws and used some glue into the holes. I used...
thingiverse
a roll cage for the traxxas trx4 sport, i tested it and it's verry strong (tumbled many times of a hill and did not break. simple and strong. There are 2mm holes in the mounting points. i used 2.5mm screws and used some glue into the holes. I used...
thingiverse
Strong roll cage for the TRX4 Sport standard body To assemble use M3 screws with cylindrical head. Attach the main part and struts to each other by directly screwing the M3 screws in the parts (screw is tapping the threads). Put the connected...