traxxas stampede 2wd 3d models
3296 3d models found related to traxxas stampede 2wd.thingiverse
Simple replacement bar for the 2wd stampede. I printed in TPU and it's indestructible. Recommended to print in ABS or best is TPU or Polycarbonate .2 resolution 100% infill. ...Higher temps and slower speeds for best strength
cgtrader
... overtighten the nut, it's only plastic that you are tightening. They might fit on a Traxxas Slash or other 1/10 scale RC cars, I haven't tried it as I don't have any other 1/10 scale RCs. Most 1/10 scale RCs with 12mm hex hubs, should work. ...
cults3d
I wanted to secure my battery wires so i designed this new battery hold down that holds and guides the wires back towards the ESC. Keeps the wires close to the battery and out of harms way. Prints easily but does need supports (at the arch) and i...
thingiverse
These are front and rear airless tires for a Traxxas Stampede. I have not had a chance to print and test these. They are designed to be printed at a low infill (<25%) with TPU (or any flexible) material. ... Please drop a comment if you try them out!
thingiverse
Update 5/12/2015 Did some bashing with the Stampede and surprisingly it has held up! Even after a few bumps! I repaired the .stl and fixed some of the geometry problems with the original. ...Now every lines up better and when the suspensions at full...
thingiverse
Custom Front Wing and Rear Wing for Traxxas 2WD ONLY vehicles Provides adjustable downforce for speedruns! </h3> This is a pair of front and rear wings that have been designed to give adjustable amounts of downforce while producing very little...
thingiverse
Rear Mount extension for larger body in a Traxxas Stampede 2wd
grabcad
Part made for Traxxas Stampede 2wd (compatible with some other traxxas models). ...Edited to produce more stability when 3D Printing
thingiverse
This is a body lowering mount for the Traxxas Stampede 2wd. It probably would fit the 4x4 but I do not have one to find out. ... Let me know if you have any other questions.
thingiverse
this is the battery cover for the traxxas stampede 1/10 scale 4x4 R/C car.
thingiverse
Designed in Thinkercad i am printing it to my Traxxas stampede may workfor other rc cars but it works for Traxxas stampede. ...You have to drill holes in it :)
thingiverse
Inner wheel for traxxas stampede or any R/C vehicle that take a 2.2 wheel and 12mm Hex.
thingiverse
Traxxas Stampede Chassis, This is an experimental part, and may require modifications, Print at your own risk Would suggest at least 80% infill
thingiverse
Replaces body mount on traxxas stampede. Not tested- ill update when I print this. ... --UPDATE-- I recently got the chance to test this, and it worked perfectly.
thingiverse
This is the V1.0 remix spoiler for traxxas Stampede. I will optimize this version as well as other pieces for stampede. I remixed the original version because the spoiler was too low for a stampede and not printable simply. ...Thanks!
cults3d
This is the V1.0 remix spoiler for traxxas Stampede. I will optimize this version as well as other pieces for stampede. I remixed the original version because the spoiler was too low for a stampede and not printable simply. ...Thanks!
prusaprinters
this is the battery cover for the traxxas stampede 1/10 scale 4x4 R/C car. Print instructionsUnassociated tags: R/C Category: R/C Vehicles
grabcad
This is a custom Chassis for the Traxxas Stampede, which has the wheelbase extended 2 1/2" and space for a 7C flat battery pack. ...Made of 1/4" thick fiberglass 3" wide and 1/8" PVC
thingiverse
20130427 Update: Now that I've a 3dPrinter, I know that rebuilding a traxxas stampede with ABS is going nowhere. Lets wait for the Taulman Nylon :) Instructions Print parts and assemble as...
myminifactory
Get the entire file at: https://cults3d.com/en/3d-model/gadget/traxxas-stampede-strong-bulkhead OR: https://www.cgtrader.com/3d-print-models/hobby-diy/other/traxxas-stampede-strong-bulkhead The bulkheads on the Traxxas Stampedes always seem to break,...
thingiverse
this is a replacement support piece for the chassis of the Traxxas Stampede RC truck. I've made it more robust than the original and printed with ASA for improved strength. I designed it so you can print it on it's side but you'll still need some...
cults3d
This is a 1/10th scale Cybertruck model designed to fit a traxxas stampede 4x4. Lexan windshield, cast acrylic side windows, functional tailgate. Cutouts for 8mm LED strips for headlights, taillights, light bar, bed lights, also underbody lights.
thingiverse
:D Get the entire file at: https://cults3d.com/en/3d-model/gadget/traxxas-stampede-strong-bulkhead OR: https://www.cgtrader.com/3d-print-models/hobby-diy/other/traxxas-stampede-strong-bulkhead The bulkheads on the Traxxas Stampedes always seem to...
cults3d
The bulkheads on the Traxxas Stampedes always seem to break, so it would be great to 3D print the replacement part and save the money when needed. I have tried other bulkhead 3D models and have tried designing one that is reinforced where the 3D...
thingiverse
I bought a very used Older Traxxas Stampede. It originally had the mechanical speed control on it. The previous owner had upgraded it at some time to an ESC, but he simply used zip ties to hold it on. I thought this was a more elegant solution. It's...