traxxas stampede 2wd rear bumper 3d models

traxxas slash 2wd rear bumper mount compatible with asciencepotato's 4wd bumper. ...It's a little fragile, so please drive carefully.

Traxxas Stampede 2wd vxc replacement Spindle

These are front and rear airless tires for a Traxxas Stampede. I have not had a chance to print and test these. They are designed to be printed at a low infill (<25%) with TPU (or any flexible) material. ... Please drop a comment if you try them out!

Simple replacement bar for the 2wd stampede. I printed in TPU and it's indestructible. Recommended to print in ABS or best is TPU or Polycarbonate .2 resolution 100% infill. ...Higher temps and slower speeds for best strength

This is a custom rear body mount for a Traxxas Stampede (Not sure if it fits other Traxxas models) Can be used for mounting custom bodies or just want something with more adjustment. ...Working on more Traxxas parts soon!

This my new cool rear led bar for my traxxas stampede! I add a support for the button LED bar. The skull was found on thingiverse, thanks to recklesstryg for the model :) I print it without bed. ...Like it ;) Edit: 25/05/2017 I made an cool...

Rear body brace to reduce damage from body clips while bashing. ... Added another version with larger body hole as the original was a little snug.

Custom Front Wing and Rear Wing for Traxxas 2WD ONLY vehicles Provides adjustable downforce for speedruns! This is a pair of front and rear wings that have been designed to give adjustable amounts of downforce while producing very little drag. ...

This is the first of many print sets for a 2wd Slash down-force system. Suitable for both drift and drag cars. When the whole system is installed your car should pull itself down and make the car squat as speed increases. This fits with and without...

8 x 3M*16 screws needed

These spacers that I have designed for my Traxxas Slash 4x4 for the purpose of Providing some spacing between the RPM rear bumper and the RPM mud flaps. The reason that I have design these spacers is because my Traxxas Slash 4x4 will not pop wheelies...

... overtighten the nut, it's only plastic that you are tightening. They might fit on a Traxxas Slash or other 1/10 scale RC cars, I haven't tried it as I don't have any other 1/10 scale RCs. Most 1/10 scale RCs with 12mm hex hubs, should work. ...

EDIT: part has been updated with tighter dimensionsa rear bumper for the 1/10 scale traxxas slashbumper arms can be found here https://www.youmagine.com/designs/traxxas-slash-bumper-arm-bracesupport brace for the rear bumper...

This mount for the Traxxas Stampede puts the SkyRC GSM020 GPS under the rear 'bed' to keep it out of the way. Quick and easy print (about an hour). This fits the stock rear body mounts. ... You'll need: 2 x M3x20mm cap head bolts (18mm also work)

Rear Left Lower Control arm for Traxxas Stampede. I printed in PLA and ran the layer lines along the angle of the shock and it has held up so far. Abs or pla+ would probably hold up better. ...Drew it according to dimensions of stock part.

This mount for the Traxxas Stampede puts the SkyRC GSM020 GPS under the rear 'bed' to keep it out of the way. Quick and easy print (about an hour). ...This fits the stock rear body mounts.You'll need:2 x M3x20mm cap head bolts (18mm also...

Here is a reasr bumper for the Traxxas Maxx rc truck to match the front bumper.

Designed to adapt Revo style bumper to the Traxxas 4x4 chassis. Fits to the rear diff housing. It currently lacks a mount for the swaybars. ...My intent is to put Summit bumpers on a Telluride and I don't see the need for sways.

Traxxas rear uprights. Stock look with a little more strength added in with rounds. I haven't printed this yet, just measured and drew it up. ... So it may need a few fixes in the future.

I didn't care for the chrome bumpers on my TRX4 Bronco and I couldn't find a rear bumper I liked on Thingiverse. This is what I created to replace my chrome bumper. ... I don't recall what infill I printed it at as I printed it a month or so ago.

Wanted a bumper for my TRX-4 with a Axial Cherokee body on it that would fit in tight to the rear of the vehicle and not hang down very low. I used a bumper mount with very little drop and as far out on the frame as I could get. Added a spare tire...

Part no: 3638 Fits Traxxas rustler.

A friend downloaded an LCG rear tower from here and the screws were off + they forgot the tie rod mounts lol, So I designed this instead. This actually fits properly and has much more adjustment available. Enjoy Check out our website!!!

A piece to make your Stampede 2WD longer.

these are the 2 pieces that make up the rear bumper mount on the traxxas slash 1/10 scale 4x4 R/C car. I've included a hitch mount on the top piece as well. Print instructionsUnassociated tags: bumper mount, R/C, slash bumper, traxxas slash Category:...

these are the 2 pieces that make up the rear bumper mount on the traxxas slash 1/10 scale 4x4 R/C car. ...I've included a hitch mount on the top piece as well.

bumper mounts for the traxxas slash 1/10 scale 4x4 RC car

Traxxas front bumper with 2 holes for 5mm LED

Besides your Traxxas 2wd chassis, you'll need a suitable rear axle for your application (Axial SCX10 for narrow rear ends, AX10 or RR10 for wider ones), a assortment of screws, many can be used from the unused chassis parts of your donor car, and a...

These wings are meant to mount onto a Traxxas Rustler 2WD, although it can be used for the Stampede and Bandit but I've not verified that yet. These are designed to give your vehicle lots of downforce at high speeds for extra stability and ease of...