trigorilla pro 3d models
71832 3d models found related to trigorilla pro.thingiverse
Anycubic Trigorilla pro specs and mcu pinout - 32bit Cortex-M3 MCU (STM32F103ZET6) 8MHz crystal - Soldered 5x A4988 stepper drivers configured to 16 microsteps (MS all to 3v3) - WIFI slot for ESP-01S - Onboard Winbond W25Q16JV 16Mbit SPI Flash -...
thingiverse
I know there's no development for the trigorilla pro mainboard on the older mega i3's. The anycubic predator run this same board, but they have it baked into marlin for awhile now. I'm not a coder, but I was able to compile it for the mega i3 config....
cults3d
I know there's no development for the trigorilla pro mainboard on the older mega i3's. The anycubic predator run this same board, but they have it baked into marlin for awhile now. I'm not a coder, but I was able to compile it for the mega i3 config....
thingiverse
... bracket for my printer so i made it myself. ...This bracket is designed for Geeetech i3 Pro B printer and Trigorilla hotbed MKS mosfet. I mount everything above mainbord (GT2560) using existed holes in printer frame. ...Pictures shows how i did this.
thingiverse
Hello, After changing step drivers to TMC2208 BTT V3.0 i have decided to design better cooling duct / tunnel on Trigorilla board. It is using 40x40x20 fan to cool down step drivers and 40x40x10 fan to cool down mainboard. Both fans are from Sunon. In...
thingiverse
Trigorilla_Pi Shortly after I got my printer I made a Trigorilla mount and stepper cooler for it, a Raspberry Pi Zero dangling free running Octoprint... ...it serves quite well but as I'm embarking on a adventure with Klipper I thought I'd try to...
thingiverse
Additional documentation I made for the TriGorilla controll board in the ANYCUBIC printer. ...
thingiverse
This is a fan support (for 92x92mm fan) for cooling trigorilla boards.
thingiverse
Bracket to mount Trigorilla Mosfet in front of PSU in original Control Box
thingiverse
I was in need of a simple way to mount my trigorilla board to my Hypercube 2020 extrusion so i made this.
thingiverse
Needed to replace the failed Printboard on my Solidoodle restoration project and I had an old Trigorilla board available. ...Remix of https://www.thingiverse.com/thing:948331
prusaprinters
Bracket to mount Trigorilla Mosfet in front of PSU in original Control Box Print instructionsCategory: 3D Printer Accessories Summary Bracket to mount Trigorilla Mosfet in front of PSU in original Control Box
thingiverse
... on so I didn't have to drill holes in the control box. Inspired by TriGorilla MOSFET Stand-off by derekbrunohttp://www.thingiverse.com/thing:2105080 This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/eKADwDW09mH
thingiverse
TriGorilla board mockup --------------------- In case you want to test your cables and case setup without risking a real board. Feel free to comment. ...Criticism is always welcome, as it helps me improve!
thingiverse
Template for Trigorilla Board. Made this to add a shelf to an enclosure that mine went into for another build. ...Included a plate as well if you just want to cover the bottom of the board.
cults3d
TriGorilla board mockup In case you want to test your cables and case setup without risking a real board. Feel free to comment. ...Criticism is always welcome, as it helps me improve!
thingiverse
This is a board mount for the Trigorilla Board. ...This mount is specially made for the Anycubic Linear Plus but it could be used in the non plus version and in the pulley version as well.
thingiverse
This is NVBigBlue's excellent TriGorilla mounting adapted to use my twist-lock keys instead of screws (I don't like those captive inserts and screws the Kossels use).
thingiverse
Working with the anycubic trigorilla mainboard (a derivative of RAMPS), I've learned that these boards can run HOT. Not just the MOSFETs, but also the stepper motors - and this is in an open well cooled housing. The way the mainboard is crammed into...
thingiverse
This is a mount for a 24V DC TriGorilla 3D Printer Heating Controller MOSFET purchased from Amazon. I used it to move the MOSFET to the exterior of my DIY plywood enclosure to keep the electronics from being exposed to excessive heat. ...It allows you...
prusaprinters
Template for Trigorilla Board. Made this to add a shelf to an enclosure that mine went into for another build. ...Included a plate as well if you just want to cover the bottom of the board.</p> <h3>Print instructions</h3><p>Category: 3D Printer...
thingiverse
It's also specifically designed to hold the Trigorilla Mosfet, and a fused switch. Dimensions: Exterior - 123mm x 130mm x 61mm Interior - 111mm x 124mm x 52mm Included are the psu brackets I used in the photo. ... These are also available separately.
thingiverse
Anycubic Trigorilla MainBoard Mockup, in three types of files (STL, STEP, X_B) for your modernization projects. And Trigorilla (ver 1.0 and 1.1) PINout PDF. All pins are checked with "M43" command and tested with "M43 T" subcommand. if you...
thingiverse
I wanted to house my TriGorilla MOSFET and make it look clean for the Hypercube 300 build https://www.thingiverse.com/thing:2517628. To make things easy I used a 40mm fan and tied it into the control side wiring. A few holes were added to allow...
thingiverse
A simple stand-off for the TriGorilla MOSFET controller (model : 3maker-3D670) : designed with clearance underneath the PCB for soldiered leads. Fits in Wanhao i3 v2 / MMS v2 control box if mounted directly in front of the power supply (as...
thingiverse
Note: If you have trouble downloading this model, you can also find it here: https://www.prusaprinters.org/social/55222-tyler/prints These are the parts I used to install a Trigorilla board (from an Anycubic i3 Mega S) in to a Monoprice Maker Select...