ts100 shell 3d models

This is a form to bend a 2.5-3mm wire into a coil as a stand for a ts100 or similar soldering iron. I used a cloths hanger, but sanded the paint off first so the hot iron wouldn't burn it. After forming the end can be cut with a hacksaw to make...

I had a few more tips than the remixed TS100 case had space for, so this is a handy little tip holder!The OpenSCAD file works by loading and cutting up one part of the case.stl (grabbed from the remixed Thing) to extract its tip holder portion, and...

TS100 Soldering Base Station I seen alot much like that but didnt really spark my attention or what i needed designed from the ground up with tolorance of about 0.25mm the 8mm rod used for solder holder is just a generic 8mm wooden dowl.. the...

The one I printed has one clasp in the center versus the updated model has 2 clasps. No supports needed. Update - tightened up the clasp fitting. Update - added large size to hold 2 more solder tips (total of 4 tips plus the one on the ts100)....

This is a form to bend a 2.5-3mm wire into a coil as a stand for a ts100 or similar soldering iron. I used a cloths hanger, but sanded the paint off first so the hot iron wouldn't burn it. After forming the end can be cut with a hacksaw to make...

I'm including links below for the TS100, two options for power supplies (I use the 19v) that will fit, sponges, and tips. Full disclosure, these are affiliate type links, so if you order through these, it will help me earn some credits toward parts...

I'm super excited to be working on my first project here :-)\r\n\r\nA soldering iron holder, another Tyes, holds onto the tip and handle with a firm clamp, securing the soldering tip in place.\r\n\r\nThe file remains in its original size, but I...

TS100 Soldering Base Station I'd seen plenty of setups like this before, but nothing really grabbed my attention or met my needs. This station was designed from scratch with a tolerance of about 0.25mm in mind. The 8mm rod used for the solder...

As a drone pilot, I really needed a nice case for my TS100 while out in the field. So I designed this. It's a nice friction fit. Note: Before you test the fit, it may be a good idea to add a little petroleum jelly to the iron. I did not need to do...

This soldering iron: http://www.banggood.com/MINI-UpGrade-TS100-Digital-OLED-Programable-Interface-DC5525-Soldering-Iron-Station-Built-in-STM32-Chip-p-1021266.html?p=M41409102656201212CI 11/03/2017 update: I've added a model for a wire tip cleaner...

Wanted an easy way to use the Dewalt USB battery adapter I had with the TS100. I liked BlaydeRunners idea but wanted to make it a bit easier to make for others. This requires zero soldering/crimping etc. Just print and hot glue onto your adapter.

... a cold metal washer into a hot print may cause significant warping.</p><p>I used ABS and didn't melt anything yet. I also have the community firmware on my TS100.&nbsp;The soldering iron might tip over with heavier cables due to being so light!

Design streams available here: https://www.youtube.com/watch?v=O_khw6cFQJs&list=PLaTs09sSqm36AyPFkkUPsmaGAmIIMUc5g&index=1 This is a TS100 case I designed because I wanted to carry the thing around, but all I had was the original packaging, and I...

Place the tip cleaner on the magnets.Place your TS100 in your new soldering standBonus step: Cable extensionThis has little to do with the stand itself, but in the photos, you can see I use wire extension from the laptop power brick that I use with...

This is a form to bend a 2.5-3mm wire into a coil as a stand for a ts100 or similar soldering iron. I used a cloths hanger, but sanded the paint off first so the hot iron wouldn't burn it.</p> <p>After forming the end can be cut with a hacksaw to...

this is the soldering iron: http://www.banggood.com/MINI-UpGrade-TS100-Digital-OLED-Programable-Interface-DC5525-Soldering-Iron-Station-Built-in-STM32-Chip-p-1021266.html?p=M41409102656201212CI 11/03/2017 update Ive added a model for a wire tip...

this is the soldering iron: http://www.banggood.com/MINI-UpGrade-TS100-Digital-OLED-Programable-Interface-DC5525-Soldering-Iron-Station-Built-in-STM32-Chip-p-1021266.html?p=M41409102656201212CI 11/03/2017 update Ive added a model for a wire tip...

It has space for four TS100 soldering tips, a spool of soldering wire, allen key and two screws. It has place for a USB-C DC trigger adapter (for 5.5x2.5mm barrels). These can be found in aliexpress (ie. It requires a magnet (i'm using a round...

I really like my TS100 soldering iron. It came in a nice but ultimately non-durable cardboard box, so I was looking for a case in which to put the iron and accessories. The best option, from my point of view, was vchan3m's design. However, since I...

This is a case I designed for my TS100. The main thing distinguishing it from other cases is the soldering stand, which holds the iron securely without requiring the user to put the iron through a small hole. The stand is also easy to operate, since...

This is my trusty TS100 holder, exclusively designed for Skadis.

Solder Tips holder for T12 or TS100 T12 https://s.click.aliexpress.com/e/_9hWYxD TS100 https://s.click.aliexpress.com/e/_AdfWVz No supports required

Ikea Skadis compatible holder for TS100 tips. ...Can hold 7 tips.

The first version of Matek TS100 GPS module mount for Chameleon frame

I added an enhancement to bbzed's outstanding TS100 Soldering Iron Stand. ... https://www.thingiverse.com/thing:2150796 This stand serves as a holder for your TS100 Soldering Iron Tips, keeping them organized and within reach.

Remix of the TS100 Soldering Iron Short Case to hold two spare tips without the soldering iron body.

This is holder for Mini soldering iron TS100 and 6+1 Bit Head and one hex key.

ts100 power adapter wall mount I make it bigger on 2% in slicer befor printing for filament size compensate.

... switch is a general-purpose one. The design requires drilling three holes into the battery adapter and re-arranging the cables. Everything else is straight-forward. [Github Repo](https://github.com/stroblme/TS100-MilwaukeeM18-SolderingStation)

This Stand Is Printable Without Support! ... I Used 3-Pin JST SM Connectors To The TS100. ... And A Flat Plug Male Connector To The Battery.