tstak to toughsystem adapter 3d models

Tstak adapter. ...To be reveted on whatever you want to tstak but Tstak 2 drawer. It doesn’t work on the tstak 2 drawer and it might not work on other toolboxes. ...

This is a adapter to allow someone install a removable work top onto a Dewalt Tstak. I used a butcher block top from home depot, and cut it down to size. I printed these in armadillo filament from ninjatek. I thought the flexibility and durability...

... tape between box and part. Also put biggest washers as you can from both sides of rivets. Part was optimised to not crack after applying the rivets. Use M4 bolts if you want to be sure. ... Holds nice you can lift multiple TStak boxes with it.

Boxes to fit one drawer in the Toughsystem Drawers

Customized version of https://www.thingiverse.com/thing:2079108 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2079108

This is a battery divider for Dewalt batteries inside a TSTAK II case.Afterwards, just glued to the case.

Dewalt Tool insert for Tstak (Thingverse problems in generating stls previews) i upload the original file DWG to make easy if you want to modify the layout.

Dewalt Tool insert for Tstak (Thingverse problems in generating stls previews) i upload the original file DWG to make easy if you want to modify the layout.

Mounting for DeWalt Tstak Chests, Maybe u need some Spacers Extra because its not so easy to redesign the whole thing to fit... ... I Also Redesigned the Clip a litte bit to Fit an M4 hex nut to use Screws

These are bins designed to fit in Dewalt Tstak or Craftsman VersaStak drawer units. Theyre sized to hold 30+ res/com key blanks. ... Assuming you're going to print a lot of them, use vase mode for quick printing.

***Needs to be test printed... ...don't have a working printer available for testing it*** ***If you print, please leave comment on fit and adjustements to be made*** Dewalt Pro Organizer Shallow Tstak / Stanley FatMax Pro Shallow cup replacement

Remixed to match the rounded part that allows the latch to snap. Original part resembled the Tough System latch despite being labeled as a TSTAK latch. Print with flat side on bottom. ... No supports needed.

A 3D printable replacement latch for DeWalt TSTAK toolboxes. ...Print with supports to allow the pins to be printed. ...We produced it out of PETG and it fits well and latches nicely.

This is a mash up idea I had to put a Bluetooth receiver/ amp with speakers in a toolbox. This is the DeWalt TSTAK system toolbox with foam insert. ...Dimensions are in the ballpark, but are approximate.

these are some lids for stanley / DeWalt TStak boxes

I really like DeWalt tools and recently decided to reorganize my workspace using the ToughSystem 2.0 tool trays, because they were super cheap in bundles during the annual holiday nightmare sale. The trays have notches on the inside edges to put in...

The cup to insert gap provides just enough margin between the two so that it doesn't create a suction lock when trying to pull the insert out of the cup. 5. Multiple divider designs. The standard inserts with no dividers is labeled with "ND". If...

There are containers to sit in the top of both the older and the new tstak organiser tubs. I have checked the files and they fit great so if you are like me and never have enough organisation then give these a try! If you use the forstner bit...

Needs to be test printed... ...don't have a working printer available for testing it If you print, please leave comment on fit and adjustements to be made Dewalt Pro Organizer Shallow Tstak / Stanley FatMax Pro Shallow cup replacement Category: Parts

This is a tray to insert into the Tstak storage case compartmants because they are quite tall and I cna get two different sizes of screws into the one compartment using this insertable tray. I printed it out of ePLA but you can probably use...

Contact: RoboCavs8479@gmail.com Parts Needed: Velcro: amzn.to/2J1eVHJ Grommet: amzn.to/2BpHgTM (Overkill but works nicely) Power Strip: amzn.to/2nXfWZU Hitec Battery Charger: amzn.to/2J1f2Tm Mountable Cable Clips: amzn.to/2P1KlkL 60mm Fans:...

Simple organizer design to separate small parts in the dewalt two drawer tstak boxes. They can easily be lifted out as needed. Several versions available depending on what you are storing. I’ve found the 2x2 to work especially well for small hardware...

Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...

I managed to break a clip to the drawer on a TSTAK IV, so I designed a new one.

This allows me to secure my drill box on top of a Tstak Toolbox stack which makes it easy to carry around with the toolbox. It might be useful for someone else - who knows? ... Use plenty of shells for rigidity.

This allows me to secure my drill box on top of a Tstak Toolbox stack which makes it easy to carry around with the toolbox. It might be useful for someone else - who knows? ... Use plenty of shells for rigidity.

Angled to fit, yet not enough room for the discs to fall out of the holder when the lid is closed. The holder fits in the compartment where the charger would sit, leaving the battery copartments free. ... Will probably fit other DeWalt 125mm...

Nesting cups for the DeWalt TSTAK clear top organiser, these suit the larger cups. ...There are some similar designs already available online but I found the fitment not quite right for my liking so it sent me to design my own. ...Enjoy!

Customized version of https://www.thingiverse.com/thing:2079108 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2079108

... red cup is version 2. **Update 20200302:** Thanks to Tony Brock, [brockoffroadparts on eBay](https://www.ebay.com/usr/brockoffroadparts) for modifying the files to add more variations of the TSTAK bins. I've added his STLs to the files list. ...