ttgo esp32 battery oled 3d models

Shopping list: * board: https://www.ebay.com/itm/SX1276-ESP32-LoRa-868MHz-915MHz-0-96-Inch-Blue-OLED-Display-Bluetooth-WIFI-Kit/383042074826?hash=item592f1638ca:g:Zd4AAOSwArNdJdsd * push buttons:...

Battery and ESP32 Holder, designed for these components: AZDelivery ESP32 Dev Kit C V4 NodeMCU: https://amzn.eu/d/6SGyJsc AZDelivery 18650 Battery Expansion Shield V3: https://amzn.eu/d/eqbEHcM You can slide different addons onto the base to allow...

This box is specifically designed for a Wemos Lolin ESP32 board featuring an OLED display that can be easily sourced from online marketplaces like eBay or Banggood at very affordable prices. I extracted the internal features from...

Made a project box for the ESP32 WROOM, with a lid for the 0.96" OLED screen. It houses multiple access points for wiring, and a small 10mm slot for the touch sensors. I use a folded piece of nickel strip used for soldering lithium cells, and wire...

Protective bezel designed specifically for DSTIKE ESP32 watches featuring OLED displays, safeguarding the screen's edges from damage. The DSTIKE logo is discreetly concealed, while a small 1.5mm LED opening allows for covert use. Additionally, the...

ttgo_2.1_1.6- widened bottom.stl : In order to accomodate a bigger/thicker battery, the bottom was widened and battery bracket walls were removed ii. ttgo_2.1_1.6-top.stl : No change **Since the bottom was widened, four M2 x 16 screws will be needed...

(if using with ESP32, use my fork here: https://github.com/ASMotionLab/Sofar2mqtt) Modifications: - Enlarged width to accept a 0.96" i2c oled display and to accommodate dupont wires. - Slightly resized footprint to accept the D1 ESP32 module (which...

A simple camera box with lid for the ESP32 Cam..

Powering the device from a 4.2 volt 2000mAh Battery: The RCWL-0516 is powered directly from the battery, and the ESP32 is powered from the same source via a small diode (to drop the voltage to approximately 3.5 volts). The ESP can safely operate up...

The ESP32 needs at least 2.5v, but can draw up to 350mA at boot-time or under a lot of load.After much research - I have concluded that the easiest/cheapest way to do this is with a since LiFePo4 battery. Thus, one of these batteries (in an AA...

Case for 18650 battery powered ESP32 devboard

This is just the wall mount holder for the TTGO T-Beam with 2.4" OLED Case .You can find the case here:https://www.thingiverse.com/thing:6481961Holes are for 3mm screws.

This case is sponsored by CALE.es, the ESP32 Screen Manager for Displays. It's a straightforward, low-poly design that utilizes an ESP32 board. This board can be easily integrated into your project, allowing you to create holes for display and other...

... upgraded. ...This new design features buttons positioned alongside the OLED display, whereas the original had them on opposite sides. ...Moreover, I opted to install a smaller DHT11 board by screwing it into place rather than using its designated slot.

I have started my journey into ESP32 devices and sensors, using Home Assistant and ESPhome. My first project was a temperature/humidity/pressure sensor, packaged into a case with a small display to put in on a shelf or cupboard. ... ESPHome:...

I have started my journey into ESP32 devices and sensors, using Home Assistant and ESPhome. My first project was a temperature/humidity/pressure sensor, packaged into a case with a small display to put in on a shelf or cupboard. ... ESPHome:...

This is remix of this model: https://www.myminifactory.com/object/3d-print-ttgo-t-beam-v1-1-esp32-lora-with-gps-neo-m8n-case-133199 For 18X18 GPS antennas and 1.3 or 0,96 inch displays. ... Maybe You will neet to postfix your model due to inaccurate...

... in development. I anticipate that the case will remain the same, but I might include an internal battery and modify the back cover. ... To assemble the components, I melted pins onto the case body and blue the MQ135 sensor to attach it securely.

For TTGO T-Beam V1.1 ESP32 LORA with GPS NEO-M8N Case Using Button Head Allen Key M3 x 8mm bolts for Case and Allen Key M2 x 5mm bolts for PCB (need 4 of each Bolts) the PLA or PETG will grab on to the thread of the bolts to secure the pcb and case...

TTGO T-Display case for a 503450 LiPo battery Modified from the original "battery options" thing located here: https://www.thingiverse.com/thing:4183337

...... It's a tight fit and you need to remove the pins of the OLED as well slimming down the adhesive of it - it might need a little readjustment too but will then stay in place. When putting it together slide in the board first, then the OLED carefully.

Remix for PLA

TTGO T-Display Case for an oversized/expanded 852540 (i.e. ...up to 1152540) LiPo Battery. Modified from the original "battery options" thing located here: https://www.thingiverse.com/thing:4183337

TTGO T-Display Case for a 103450 LiPo Battery. Note this is LARGER than the 503450 (103450 is 10mm thick, 503450 is 5mm thick). ... Modified from the original "battery options" thing located here: https://www.thingiverse.com/thing:4183337

I added extra support for the board, made the case thicker on the bottom and added screws. It is pretty rugged now. ...The buttons need repositioning as they don't line up 100%.

Below can be stored a **18650 battery** (_with a single battery clip holder_) and there is still space for a **433mHz** sender (_XY-FST_). The buttons are very fragile, when the lid is not mounted. So be aware of bending them (_at least if you...

I designed this as housing for a project to communicate with solar inverter and utility power measuring device. Out of the box this board has everything to be a gateway from Canbus and/or rs485 to the network. I use its rs485 interface with...

I create my own model since admiral99 is not available right now. ...The current design of this enclosure requires significant improvements.

A compartment, which houses my **TTGO T5s 2.7"** eInk display.\r\nBelow can be stored a **18650 battery** (_with a single battery clip holder_) and there is still space for a **433mHz** sender (_XY-FST_).\r\n\r\n\r\nIt will stand on 45°, with the...