ultimaker calibration 3d models

Simple Ultimaker Calibration Tool. ... This is an improved version: https://www.thingiverse.com/thing:81415

While Ultimaker provides a STL for calibrating the Ultimaker 2/3 printers, they don't do the same for the S5, which is a shame as the S5 has different sized guide rods so the existing tool doesn't work. For instructions on how to calibrate the...

A small simple 1mm thick motif to test the Ultimaker XY print resolution. ( 36m x 28mm x 1mm)..... Feel free to compare with my results ( see attached image which is a scan of the object on a flatbed scanner with 'mm' ruler alongside). My...

Simple holder which clicks into place in the hot-end of the Ultimaker 2 printers and when completed with a cheap tire profile measuring tool give very accurate build-plate adjustment possibility. Two versions, straight which will have the display...

Place above the bottom wooden piece of the print head and block with nut. Move the bed until tip touch platform then move print head to each corner and adjust the bed until pen can draw a solid line over perimeter. ...Adjust z end-stop, remove pen...

Use two of them to align the axis rods on an Ultimaker Original. ...This one is laser cuttable.

I use this calibration tool to calibrate the 1 mm space between the build plate and the nozzle on my ultimaker 2 extended. ... Instructions Print with 100 % infill.

USE THESE GCODE FILES AT YOUR OWN RISK AND ONLY ON ULTIMAKER 2 Instructions Load the gcode in your UM 2 to start the test. Look at the results and decide what temperature works best for your material. Different layer heights result in different...

Description: 3 + 3 different GCODE files for Ultimaker 2 made with the default CURA settings and temperature range from 220C tot 190C in steps of 5C. Printing features: Straight wall Overhang (circular) Overhang (45 degrees) Curved surface Flat...

Customized version of http://www.thingiverse.com/thing:1298948 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1298948

... the 6mm rod parallel to the 8mm rod on the Ultimaker 2 Aluminium. ...Print in pair and use what variant you like. Print Settings Printer: Ultimaker 2 Aluminium Rafts: Doesn't Matter Supports: No Resolution: 0.32 Infill: 15% How I Designed This Sketup

https://www.thingiverse.com/apps/customizer/run?thing_id=1381839 Instructions Using the following options: machine = Ultimaker 2+ PLA temperature = 215 C BottomSpeed = 20 TowerHeight = 136 TowerSide = 20 HeightIncrement = 8 SpeedIncrement = 5...

https://www.thingiverse.com/apps/customizer/run?thing_id=1381839 Instructions Using the following options: machine = Ultimaker 2+ PETG temperature = 220 C BottomSpeed = 20 TowerHeight = 136 TowerSide = 20 HeightIncrement = 8 SpeedIncrement = 5...

Customized version of http://www.thingiverse.com/thing:1298948 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1298948

Customized version of http://www.thingiverse.com/thing:1298948 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1298948

Customized version of http://www.thingiverse.com/thing:1298948 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1298948

Customized version of https://www.thingiverse.com/thing:1381839 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1381839

Customized version of https://www.thingiverse.com/thing:1381839 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1381839

Customized version of https://www.thingiverse.com/thing:1381839 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1381839

One day, I wanted to make an automatic table calibration on my Ultimaker plywood. Inductive, piezo, tenzo, and other sensors did not suit me because they either took up the workspace or caused problems with the installation of cooling fans for the...

I seperated them to 2 parts so you don't need to use any supports but they need to be glued together

Ultimaker OSHW project (ultimaker.com)

... Instructions Print at 100% fill, you'll want a slicer that can fill thin walls. Clean out the respective holes with a 6mm and 8mm drill bit. This is the link to instructions from Ultimaker for aligning your axis http://wiki.ultimaker.com/Calibrate

calibration part

Calibration. Gauge matryoshka. ??????????. ????????????? ...????????.

My personal calibration test

Part for calibrating printing speed, temperature and layer height

Test de calibration : comment déterminer la température d'impression optimale en fonction de votre imprimante 3D (2 fichiers : STL , GCODE) Calibration test : how to determine the ideal printing temperature for your 3D printer (2 files : STL , GCODE)

This is a simple diameter and height calibration print dimensions are 30 x 30 x 20 (L x B x H)