under the desk shelf 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=1337584 Instructions Using the following settings: Radius of inner edge: 5 units Wall thickness: 3 units Radius of outer edge: 5 units Cable diameter: 25 units Height from desk surface: 51 units...

A simple and elegant hook that magnetically attaches to the underside of a desk and holds headphones. There are 2 slots for 13*3 mm round magnets, although smaller ones would likely be strong enough. ...It does need to latch onto some sort of ferrous...

This bracket allows you to mount the female side of the break away cable to the underside of a desk. ...When you want to use the Index, you can simply plug in the male side and it stays supported while still being able to break away if needed. If the...

I printed the back with 2 helper disks - just in caseThe limiter stops the drawer from falling outTray Insert (use with the Tray version of the Drawer Front)Bonus - locking limiter stops causal snoopersAttaches to the underside desk with 4 small...

It screws into to the under side of the table. Screws are not necessary to attached the magnet to the plastic since it is a very tight pressed fit. ...You'll want to make 2 of these but mirror one in your slicer to get a left and right version.I used...

I also designed it to move the hub down from the surface of the desk as well to make it easier to use SD cards. I have three brackets, an open one, one that can be used on the front, and one for the back. ...I've attached pictures of the hub that I'm...

To keep it organized, I built a holder and screwed it into the underside of my desk, out of sight. The remote slides smoothly inside but stops short, as both the device and its holder are tapered. Print Settings Printer Brand: LulzBot Printer: TAZ 5...

i design this for fix my wacom intuos 4 ender my desk

See other models for my desk at https://www.printables.com/@Morbier/collections/1571699

Will fit most desks or similar table tops 3/4" thick. ... No Glue, No Screws.

To achieve this, you'll simply attach two mounts to the underside of your desk or table using glue, such as Tesa Power Strips, or screws. This clever design allows you to hide your keyboard when not in use. ... The screw holes on these mounts are...

So....I created these holders that once installed, allows you to remove the adapter easily without tools when you need to take your laptop with you on the go. Simple, effective, and easy to print. ...They are for ASUS 17" & 15" ROG laptop adapters,...

My Hue Plays wouldn't stick to the curved back of my monitor, so I decided to mount them to the underside of my desk instead. As I didn't know at what angle they would look best, I designed a mount that would offer me to adapt their orientation...

Highlights:Print time less than 20 minutesUses only 5.5 grams of filament per objectScrews in to desk using either #6 screws (M3/M3.5 equivalent) or you could use command strips for a less permanent solutionDoes not require supports!Two slots to...

I designed this mount so my Vive headset would hang securely from the underside of my desk. The left and right brackets are mirror images, carefully crafted to hug the contours of the headset closely. When positioned correctly, the brackets keep...

This is a straightforward mount designed to conceal the USB hub/switch, resulting in a tidier desk area. The design includes MAIN.stl, which serves as the primary unit and must be printed twice. This ensures that the main unit remains securely in...

To solve this problem, I designed these holders so that the headphones fit snugly just behind the desk's edge, preventing them from getting knocked off or in the way. ...Additionally, I made sure to include a feature for looping the cord behind the...

This is a convenient way to store and use the remote as if it were built directly into your standing desk. No need to have the remote cluttering up your workspace or having to dig it out of a drawer. I sliced with Cura 5.4.0 and added tree...

I have several desktop dac/amps that I printed mounts for, but the Fosi k5 I use for gaming was not being shown any love. I used #6-¾" construction/wood screws to mount it to my desk. The front stops behind the bezel and the rear catches on back...

This design has a small gap to separate the Mac from the desk to avoid trapping heat and causing throttling due to heat. The Mac can be mounted upside down, but I wouldn't advise it. ... This can be also used to wall-mount it both with the cables...

This is made for a desk that is 2 cm thick. ... Remixed from @zitcon_home Original @pixi2012

Simple mount for y'all to mount your Macbook pro 60 watt chargers underneath your desk for cable management purposes.

... Print two of them and position them inside the legs. Then, simply hook it over wherever you want to set up your new device. The Sketchup file is included if you need to adjust the sizes to fit a different mounting configuration or computer setup.

I needed to mount headphones to the underside of my desk, so I remixed my old headphone hanger design to accommodate this new mounting requirement. This model also contains infill modifiers around the screw/bolt holes to create a solid ring a little...

... nespresso holder for my own demands. ...We have a deep shelf so I enlarged the rail to use as most space as possible. Could be still printed with standard bed size like Mega S. ... (updated for more stability) Official link : www.nespresso.com

The Fosi DAC-Q4 sits securely under a custom-fit mount, firmly locked into place by its snug fit within the mount's design. The DAC-Q4 rests comfortably against the adjustable mounting system, which allows for precise positioning between its...

... of the hook, one with relief for the head of a socket-head cap screw and one without. Which one you use will depend on what hardware you have available. The mounting hole is to fit an M5 bolt which is what is on the underside my Ikea desk.

Desk-underneath headphone or headset holder, equipped with no need for supports. ... If you enjoy this item and can sacrifice a couple of satellites: Bitcoin: bc1qxzm768ypwxfwc8rkqk98vk3m3vrea6udqpup5u

My glass-topped office desk features square frames measuring 25mm on each side, so I came up with this straightforward hook to clamp onto the frame and keep my headset within easy reach while keeping it out of sight when not in use. To add a bit...

To keep my headset within easy reach while keeping it out of the way when not in use, I created this straightforward clamp that attaches to the frame. For added strength, I rounded most of the corners with fillets, though they're probably...