unifi uap ac pro 3d models

The support for the POE of Ubiquiti Unifi UAP AC PRO model (48V)

For mounting UniFi UAP-AC-PRO horizontally when ceiling mount is not ideal. Designed by request. ... For UAP-NANOHD: https://www.thingiverse.com/thing:4143266

The UniFi AC-Pro is listed as an outdoor Access Point but it's not designed to be installed on the side of the building without a substantial overhang to protect it. I needed to install a couple on a barn with minimal overhang and a large gutter...

The UniFi AC-Pro is listed as an outdoor Access Point but it's not designed to be installed on the side of the building without a substantial overhang to protect it. I needed to install a couple on a barn with minimal overhang and a large gutter...

after installing my Ubiquiti unifi network in didn't want to hang the ap's to the wall or sealing. so i design a vertical mounting bracket to place on a table of tv stand based on the makerbot headphone stand. ... needed: -3 m3 nuts -3 m3x10 screws...

after installing my Ubiquiti unifi network in didn't want to hang the ap's to the wall or sealing. so i design a vertical mounting bracket to place on a table of tv stand based on the makerbot headphone stand. needed: -3 m3 nuts -3 m3x10 screws...

Want to mount a UAP AC Pro at home on a concrete ceilling and don't want to see the installation cable? Don't want to bend the installation cable or to cut it right below the ceilling? This adapter gives the installation cable about 25 cm more...

Remixed to use less filament and print faster. Cutouts leave enough area for adhesive mounting. ... Source files provided to enable further tweaking.

This remix adds screw mounting holes and some cutouts that reduce filament usage and possibly add strength. I also shaved off about .3 mm of height from the bayonet because it was a little too tight. Sketchup was hating me so I used 3D Builder. ...The...

Unifi UAP-AC-M-PRO Corner Mount Bracket

One piece or clamshell style cover for the Ubiquiti Unifi AC Mesh Professional UAP-AC-M-PRO. The cover is mostly intended to change the color of the device, it is often mounted outside on buildings and the white access point can be very jarring...

This is an adaptor to allow you to mount a UniFi piece of equipment to a standard ethernet wall socket. ...It reuses the existing wall fixings and the fixings that come in the UniFi kit (tested on AP-AC-Lite and AP-AC-NanoHD.

Das ist ein Remix von Pelphry17's "UniFi UAP-AC-PRO Horizontal Wall Mount". https://www.thingiverse.com/thing:4313681 Ich habe anstatt der 4,5mm Bohrungen 4mm Gewinde hinzugefügt. ...Weiterhin habe ich die 4 Montagebohrungen auf zwei reduziert.

... 20mm self-adhesive magnets. If you look closely, you can see I had to shave off a bit on two of the edges, to make it fit on my print bed. Used Tinkercad to make this: https://www.tinkercad.com/things/klecvG8bV6b-unifi-uap-ac-pro-magnetic-mount

For mounting nanoHD (UAP-NANOHD-US) horizontally when ceiling mount is not ideal. ... Easy 1.5 hour or less print. For UAP-AC-PRO:https://cults3d.com/en/3d-model/tool/unifi-uap-ac-pro-horizontal-wall-mount

Mount for a Unifi UAP-M Accesspoint You need 2 M4 screws with countersunk head and the included screws from the Accesspoint.

Stand for Unifi UAP-AC-LR Use 4 M3 screws and 4 nuts Remix of two other mounts

Unifi UAP-AC-M Antenna block

This is a wall mounting bracket for a Unifi UAP-AC-M outdoor access point.

Drill template for UAP-AC-IW

Corner mount for Unifi's UAP-AC-M access point. For use outdoors, print in a suitable material such as PETG and ideally paint it too. Use a high infill for strength and set wall count to 7 (with 0.4mm nozzle) which will provide a continuous line...

Antenna holder for the mount for the Ubiquiti Unifi UAP-AC-M Mesh AP. This holds the included antennas at the recommended 45º angle, and should help prevent weather, birds, etc. from knocking them out of position. The holes are ellipses, and not...

I needed a mounting bracket for a Unifi UAP-AC-Lite I got which did not come with one. This is similar to https://www.thingiverse.com/thing:2196922 (which did not work for me because the mounting tabs were in the wrong places) but was built...

This is a semi-waterproof enclosure for the UAP-AC-LITE. Note that the above statement says semi; it is watertight, but I don't want anyone to assume they can mount it in their pool. Mine will be mounted in a cool area; I would not recommend...

I created this standoff as i wanted to cover my network socket at the ceiling. ...It is desgined for the **UAP AC Lite** and the **WiFi 6 Lite**, but should also work for all other Unifi APs with the same dimensions.

This is a mounting bracket for a Unifi UAP-AC-M (AC-Mesh) Access Point to mount on a standard german junction box that allows you to hide the network cable nearly completely. The dimension of the plate is 80mm x 80mm, the gap of the screw holes is...

#Wall box for a Ubiquiti UniFi UAP-AC-IW access point **Update 7/25/2019:** Added second model with stronger screw supports [These access points](https://store.ubnt.com/products/inwall-ap) are designed to mount like standard face plates over a...

Assembly Instructions: To assemble the Universal UAP-AC-Pro mount first use a soldering iron to install the threaded inserts. After all three inserts have been installed place the UAP bracket that is included with your access point over the three...

This is a remix of jdcraymond's Ubiquiti UAP-AC-Pro Horizontal Wall Mount. ...My printer struggled to print the original and it wasn't as strong as I would have liked, so I made a couple modifications that made it better suited for my needs.

This mount is to mount the Ubiquiti UAP-AC-Pro horizontally on a wall as this is a best orientation for it. I discovered there was 2 different orientations of mounting holes. This will support both. The metal ceiling plate that comes with...