upgrade flashforge creator pro 3d models

... the back plate, plus inserted slots for securing M3 nuts on the rear bracket for a tighter grasp when assembling the parts. ... Print Settings Printer: Creator Pro Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.20mm Infill: 40% or greater

... into the existing cooling fan and utilizes the same screw holds. Print Settings Printer: Flash Forge Creator Pro Rafts: No Supports: Yes Resolution: 200 Micron layers Infill: 20% Notes: Print from ABS or PETG to resist heat from the extruders.

But in this case it is adapted for Flashrorge Creator Pro: 1. Depth made less at 5-6mm to fit back decorative wall; 2. Added a hole for fitting near the screw; 3. Made bottom thicker 0.75mm for resin printing. Printed on resin phrozen mega 8k...

... bracket for better grip when connecting the parts. To print this project, you'll need a Creator Pro printer with the following settings: Rafts don't matter, supports are optional, resolution is set at 0.20mm, and infill should be 40% or greater.

This customizable bracket fits the FlashForge Creator Pro and printers with similar build plates with M3 bolts at their corners. The adjustable knob makes it is easy to swap out glass plates if you have more than one, so you can start printing on...

The versatile adapter perfectly complements the user-friendly FlashForge by providing a convenient platform for easy tool access and effortless workflow optimization.

I did hot glue it in place but I am thinking of designing and printing a spacer to place between the filament guide and the inside of the Creator Pro, possibly eliminating the need for hot-glue. Printed at 40% infill and I will be adding some low...

I did hot glue it in place but I am thinking of designing and printing a spacer to place between the filament guide and the inside of the Creator Pro, possibly eliminating the need for hot-glue. ... Printed at 40% infill and I will be adding some low...

The spools of filament I purchased refused to seat properly on the standard spool holder supplied with my FlashForge printer, which boasts a 66mm x15mm spacer at its base. In stark contrast to the spools that came bundled with the FlashForge, the new...

With my Flashforge, current models didn't fit very well and required modifications to enable the Extruder idler to open freely. I also wanted to simply use the included center brace to manage cables effectively. Here's my remix. I've printed and...

This is an add-on to http://www.thingiverse.com/thing:735350, engineered to secure split loom (1/2" or stock Flashforge) covered wiring in place. The original design's small filler piece was deliberately omitted for this iteration. To ensure a flush...

If the M104 was in the start script then you would have do disable the other extruder like Egurs profile or have whole different profiles for each side like Lyl3s profile. ...So you need to make sure that you have a skirt around your print because this...

... been using the 2016 edition of my multi-width bracket, and it turns out that's actually designed for the 2015 model. ...Because of the open clips on the v.2016 Creator, this bracket may not grip as securely as the one made for the 2015 version does.

Print Settings: Printer: Flashforge Rafts: No Supports: Yes Resolution: .2 Infill: 75% Notes: It must be quite strong, so ABS or PETG supports might be necessary for the large hole (PLA cannot handle motor and hot end heat). ...This is a work in...

... ABS (using 230C/110C heat settings for extruder/bed) Medium speed 20% infill Finally, hit print and you're ready to go! Here's a link to the Tinkercad model: https://www.tinkercad.com/things/5clJPy6WEL2-flashforge-plug-dual-color-with-supports

... following were defaults (which I kept): ABS (I use 230C/110C heat settings for extruder/bed) Medium speed 20% infill Ok, then print! Here's the Tinkercad link: https://www.tinkercad.com/things/5clJPy6WEL2-flashforge-plug-dual-color-with-supports

The ultimate upgrade is here, with a revolutionary drop-in replacement for those flimsy snap tube holders that needlessly require a zip tie. Simply install it with the factory-provided screw, effortlessly securing your print job. To make the most of...

I upgraded my FFCP just before active cooling fans became a standard part of printers, roughly a month beforehand. It's always been a challenge managing the active cooling system. I've finally had enough and ordered a substantial 120mm fan that plugs...

Print: \r\n- 4x M3 Screw End\r\n- 1x Alu carriage blower\r\n\r\n This allows you to use the "turbo fan" (or any similar 24v blower fan) with the Chinese upgraded x ends and carriage. The active cooling duct is heavily inspired by a design this...

THE GO-3DPRINT.COM BRAND BOROSILICATE GLASS OFFERS A WONDERFUL UPGRADE OPTION. HOWEVER, THE GLASS PLATE IS SIGHTLY THICKER THAN OTHER GLASSES ON THE MARKET. I DESIGNED THESE CLIPS TO ENSURE THE 3MM THICK GLASS IS LEVEL WITH OR EVEN HIGHER THAN THE...

This shim is designed for the glass products sold on this website:\nhttps://www.flashforge-eu.com/parts-and-accessories/frosted-glass-build-platform\nPrint Parameters\nMachine: \n Flashforge Creator Pro\n \n Raft Settings: \n Disabled\n \n Support...

Reimagined Stepping Block: Filling the Void Left by Your Missing Left Stepper This custom insert seamlessly occupies the space where your left stepping component was removed.

Hand tool holder that installs on the side in convenient carrying slots. ...Holds nearly all standard tools required for frequent printer upkeep and repairs.

I build a robust filament spool holder with a durable 608-2RS ball bearing and a sturdy 8mm galvanized steel threaded rod for each holder. To assemble each spool holder, you will need to print several parts: One substantial screw (screw.stl) to...

Craft a Simple Enclosure for Your FFCP Printer to Reduce Noise and Retain Heat. A Filter Can Be Added to Eliminate Odors Caused by Various Filaments During Printing. Built with +/-5mm Sheet Material in Mind (5.5mm Gap/Openning for Your Preferred...

We Must Shrink Hole Openings to an Absolute Minimum

This spool holder is incredibly easy to use for the FFCP, consuming hardly any filament along the way while printing at incredible speeds!

No Extra Parts Needed Only 3 Parts To Print No Supports Needed Part Cooling Built Into Carriage I printed in PETG 100% infill because all parts are small and thin Parts are oriented in the best print position Also if you edit firmware...

I designed this tool using Tinkercad. Print two copies. Changing spools becomes a breeze from the front side now. As printed, the tube clears the wiring and the rear-mounted filament guide (just remove those filament guide tubes). The holder is...

I picked up some spool holders on my second-hand CNC machine and these are exactly how they looked when I got them. ...They function perfectly and possess a sturdy build.