upgrade flashforge creator pro 3d models

... I recommend using the E3D V6 extruder. Follow my project here: https://crunchysann.com/BL/projects/ Print Settings: Printer Brand: FlashForge Printer: Creator Pro Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.3mm Infill: 20%

... in Yafo. Print Settings: Printer: FlashForge Creator Pro Rafts: None Supports: Not needed Resolution: 0.3 mm with three shell layers Infill: Twenty percent density Notes: This is my preferred printing method, yielding successful results every time.

This is a reworked adaptation of Stigern's 0.25" Z-axis spacer for the FF Creator Pro.\nI'd procured a 5mm glass bed from my local vendor, so I rewrote it to create a 5mm version of my own. During that process, I also designed a 3mm edition.\n\n \n...

Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 50% Notes: I used Simplify3D for the slicer. Please see the attached settings. How I Designed This: I tried various glass plate holder designs...

These are custom designed shims that have been perfectly matched for use with a Flashforge Creator Pro, which was built mid-2015. They are specifically designed for 3mm or 4mm glass bed upgrades of similar size. Instead of leaving a gap around the...

If you have a Flashforge Creator Pro/Pro2, print the "holder" with the short side touching the build plate (if you have good bed adhesion there's no need for brim/raft, but you can use a brim if you wish) and use PETG filament with >40% infill for a...

Flashforge Creator Pro Y-axis step motor mounting bracket redesigned for added strength compared to the original factory part. A cutout accommodates the belt, minimizing any interference with its placement. Two versions are available: one with the...

I recently purchased a FlashForge Creator Pro for rapid prototyping at work and found that the included filament spool holders were excessively large in diameter to fit my stock of Hatchbox filament spools. Unlike other designs on Thingiverse, this...

Flashforge Creator Pro Y-axis step motor mounting bracket. I modeled a stronger design verse the factory bracket. I thought the belt was very close to the bracket so I created a version that has a cutout for the belt. You can select which one you...

A modified z-axis limit switch shim based on salbemerson's design for use with the Printz Printer Plate on the FlashForge Creator Pro. The plate measures approximately 1/8" thick or around 3.35mm. It was printed at low resolution and installed on...

This is a custom Raspberry Pi 3 sleeve case featuring a camera ribbon cable pass-through, designed specifically for replacing a spool holder on Flashforge Creator Pro. This innovative design thoughtfully maintains the existing spool holder rather...

You'll need some M3 screws and nuts, of which there are several extras in the hardware bag that comes with the FlashForge Creator Pro. ... One note: if your creator comes with a back plate behind the build platform, you'll need to remove it or it will...

This is a custom filament spool holder designed specifically for the Flashforge Creator Pro, suitable for use with 3D Printz stock filaments. While the standard holder performs admirably, it can be prone to allowing the 3D Printz roll to slide off...

I find that on my FlashForge NEW Creator Pro (received November-2016), parts with large surface areas are difficult to remove from the bed plate. For example, the first time I printed out the orange bird house (thingi1351023), I did so on a glass...

made specifically for spools I get from 3D-factory in yafo Print Settings Printer: flashforge creator pro Rafts: No Supports: No Resolution: 0.3 mm and 3 shells Infill: 20 Notes: that's how I printed it, works fine for me Category: 3D Printer...

Printer Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Doesn't Matter Resolution: 0.2 mm Infill: 20% Post-Printing Make sure the shim is perfectly flat to avoid springiness while pushing the Z endstop switch, which could...

There are many shims available but I couldn't find any for the 2016 FlashForge Creator Pro which seems to have screws in different places than other models, so here's a remix that fits. Ready-to-use models are available in thicknesses from 2 to 6 mm...

... Thanks, fdk. Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: .20 Infill: 20% Notes: 3 top layers, 3 bottom layers, 2 outline perimeter shells printed on a 95-degree bed at 235 extrusion temperature with ABS.

Unfortunately the FlashForge Creator pro lacks a fan speed controller, because the fan is hooked up to the EXTRA output of the mainboard, which can only be toggled, it has no PWM capabilities. It is possible to create and install a custom build of...

Unfortunately, the FlashForge Creator Pro lacks a fan speed controller because the fan is hooked up to the EXTRA output of the mainboard, which can only be toggled and has no PWM capabilities. It's possible to create and install a custom build of...

The parts are for upgrading the FFCP with 4x2mm bowden tubes. because of the higher flexibility. ... BR Sepp

The mount is strong and perfectly fits my QIDI Tech printer; I'm confident that it could also be used with Flashforge printers. In one picture, you can see me testing it with my utility bin. Print Settings Printer: QIDI Tech ...

I upgraded my Flashforge Dreamer by removing its noisy stock 80mm fans. This upgrade lets me mount two standard 120mm, 12-volt PC fans which are generally much quieter. In the photo, they're running off an external 12-volt power source but later I...

Print Settings Printer Brand: PowerSpec Printer: PowerSpec 3D Pro Supports: No Resolution: .2 Infill: 20 Notes: I recommend PLA. ...Everything can be printed at .2mm layer height except for Pi_Zero_Case_Camera_Swivel.stl, which must be printed at .1mm...

Still working on that part. I added just the case bottom with no mounts for other projects. Print Settings Printer Brand: PowerSpec Printer: PowerSpec 3D Pro Supports: No Resolution: .2 Infill: 20 Notes: I recommend PLA. ...Everything can be...

I modified the filament guide to suit my needs. The diameter of the securing rods was altered to 5.8mm due to difficulties with clicking them into place. ...I adjusted the distance from the rear of the printer to the center of the guide tubes to 35mm.

I reinforced the frame by adding an extra attachment point and tweaked the air channels to perfectly align them with my flat flexible cable connector.

This adapter mounts to the original spool holder allowing you to use third party filament reels.

An OctoPi OctoPrint mount for an Aukey Webcam that fits underneath the print bed. ...This is a friction fit and may need to be slightly adjusted for your configuration.