valve index fan 3d models

The 3D model was created on real base. ...It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.

Hi I am Frezzy from Vnvisual studio.

I made this cable guide to route the cable better when using an overhead cable management system and to allow the cable to flex over a longer section to reduce pinching. The tolerances are pretty tight so you may need to slice open the gap where...

Just a simple remix. Did not like the gab that was in there (caused unneeded support). Made it a little thinner to decrease built time and overall bulk coming from the holder -- moved the center of gravity to be more near the wall. I used simple...

The detailed three-dimensional rendering model of the Generation Two Base Station is readily accessible within the confines of the Steam Virtual Reality driver software package.

Note: The v2 files have more forgiving dimensions for the cable pass through channel. I've modified my original design (https://www.thingiverse.com/thing:3886099) for those who are looking for something a little different. There is nothing wrong...

Can be mounted to a back plate with #6 wood screws, or directly to your wall with [medium Command strips](https://www.command.com/3M/en_US/command/products/~/Command-Medium-Picture-Hanging-Strips/?N=5924736+3294529207+3294774739&rt=rud).

The only component that has been thoroughly tested is the controller stand. The HMD hook, however, remains unprinted and untested, though it's expected to fit properly. ... Update March 31, 2020, 10:00 PM I've made some minor adjustments to the rear...

An exotic stand for exotic controllers; This organic concept leverages the natural center of gravity of the knuckles to cradle them in a stable orientation with a minimalistic design. <b>Warning</b>: Hanging the knuckles on the stand is...

Using a ceiling cable management system can be super helpful, but be aware that the clamp can technically be installed almost anywhere. ... It snaps into place very securely, making it a tad challenging to take out without causing some damage.

My strap release button broke and I was out of warranty, so i remade it, using the top half from the official CAD model and the bottom half as an approximation from the pieces I could find. If you've lost the original springs, you gotta find some...

You'll have to attach the logo carefully if it's not a snug fit. It might be necessary to smooth out the logo with some sanding for it to sit properly within my tolerances. My precision isn't quite there yet. Once printed, you should apply some...

Credit is due to Thingiverse for making available at https://www.thingiverse.com/thing:3772599 and also for the model located at https://www.thingiverse.com/thing:4270682

This is a kitbash of two magnetic mounts for the Vive Facial Tracker for the Valve Index HMD. I combined the best attributes of the two and added a spot for a 40mm frunk fan as well. Use K&J Magnetics DH13 1/10" x 3/16" disc magnets for the...

Detailed 3D model replica of Valve Index VR headset with controllers and sensors

Simple and easy valve for 80mm computer fan. You will need a plastic sheet. ... Print the "Clips" (clip) on a side and the "Plaque" (slab probably) with the little spaces (for the clip) upward to have the cleanest surface in contact with the plastic...

- 4x M5 25mm screws and nuts to attach servo and sprocket to the top tray - 8x short M3 screws to attach relays - 4x short screws (M3 max) to attach valve to the fan - 4x short m2 screw to attach ESP32 - self adheasing sealing tape 12x3mm to seal...

A spacer that increases the height of the USB C connector on the charging cable that came with the Valve Index Controllers so you can plug it in by just putting the controller in.

A ball-joint mount for the HTC vive or valve index lighthouses designed to go in a room corner on picture rails. ... Printed in PLA on standard settings although I'm sure other settings will work.

Once piece slot style mount for valve index base station 2.0's. these let you use command strips or some other form of adhesive mount for the base stations as apposed to screws. I recommend you print these vertically slot up. ...snug fit and allows...

I decided to try and think of a new way to make the stock compatible with the Valve Index, and came up with this design. I had three main purposes with this design: - Move the index controller to underneath the stock rail - Angle the controllers to...

Updated 24 FEB 2020 This contains only the parts needed to use the Valve Index with the excellent NoobTube gun stock created by Toposolitario: * Right controller grip and clamp * Grip (v2.0) allows Index with handle booster to fit * Grip (v.2.1)...

These are for Valve Index Knuckles and HTC Vive 3.0 Trackers. ... I have made two versions for flat head chargers and round head chargers (thinking about magnetic chargers for my personal use) Whatever infill is fine I would suppose, printing mine out...

Charging cable adapter fix for this model https://www.thingiverse.com/thing:3751848 The original charging cables from the Valve index are to deep and loose. I tried out an other version somebody made, but it doesn't worked. This one should be...

These are for Valve Index Knuckles and HTC Vive 3.0 Trackers. ... I have made two versions for flat head chargers and round head chargers (thinking about magnetic chargers for my personal use) Whatever infill is fine I would suppose, printing mine...

I bought these lamp tripods for not having to drill holes in my walls to mount the basestations for my Valve Index. But when I got the tripods, I noticed the top part doesn't swivel. ...So I designed this adapter that you can screw onto the camera mount...

DescriptionDetailed 3D model replica of Valve Index VR headset with controllers and sensors Detailed sufficient for close-up renders Perfect topology All the parts have their original stacked modifiers so its easy to customise in 3ds max. Enclosed a...

I own both a Valve Index and an Oculus Quest. I previously owned a Rift CV1 so I have VR Lens Lab prescription lenses, but they don't fit either of my current headsets. These magnetic adapters let me swap the lenses easily. Remixed these designs by...

I own both a Valve Index and an Oculus Quest. I previously owned a Rift CV1 so I have VR Lens Lab prescription lenses, but they don't fit either of my current headsets. These magnetic adapters allows me to swap the lenses easily. Remixed these...

I bought these lamp tripods for not having to drill holes in my walls to mount the basestations for my Valve Index. But when I got the tripods, I noticed the top part doesn't swivel. ...So I designed this adapter that you can screw onto the camera mount...