valve index frunk mods 3d models

The only component that has been thoroughly tested is the controller stand. The HMD hook, however, remains unprinted and untested, though it's expected to fit properly. ... Update March 31, 2020, 10:00 PM I've made some minor adjustments to the rear...

You will have to glue the logo in if it isn't too tight. You might need to also sand the logo for it to fit. My tolerances aren't perfect yet :( Once printed you should probably put some adhesive craft foam or something to keep your headset from...

ImportantPlease try the cables before printing. Display Port can be finicky and an extension cable might not work for your setup. ...For me only a very short cable of 2 meters worked.Required Hardware4 wood screws 3.5x16 for mounting on the desk (don't...

Modeled from scratch in Fusion 360. I'd print with at least 4 perimeters and with the orientation as shown in the model view to ensure rigidity. The one pictured was printed in PLA. Doesnt show any signs of flexing or breaking. The chamfered edges...

The detailed three-dimensional rendering model of the Generation Two Base Station is readily accessible within the confines of the Steam Virtual Reality driver software package.

Human: Modeled from scratch with precision and care, this 3D printed accessory was created using Fusion 360 software. Printed with a minimum of four perimeters and carefully oriented as shown in the model view, it boasts exceptional rigidity. The one...

My strap release button broke and I was out of warranty, so i remade it, using the top half from the official CAD model and the bottom half as an approximation from the pieces I could find. If you've lost the original springs, you gotta find some...

Hi I am Frezzy from Vnvisual studio.

The 3D model was created on real base. ...It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.

I wanted to create this because for me it was annoying to stop/pause the printing to change the filament (color) for the middlepart if you want multicolored. Easy to print (30-40min) in any color you wish. ...simple to install - glue it, done!

Hi I am Frezzy from Vnvisual studio. This high-quality, photo-real model is designed to elevate detail and realism in any rendering project. The fully textured, detailed design allows for close-up renders and was originally modeled in 3ds Max 2012...

They sit perfectly in the groves, I made it for you guys :)

Printed, but never mounted.

This is my final design of my LENS LAB ADAPTER modification (ting:2903956) which is now: - Smaller - does now fit on --> HP REVERB G2, --> VALVE INDEX and --> HTC VIVE (PRO). It is an adapter to use LENS LAB LENSES and (as replied by SKETCHY7)...

Credit is due to Thingiverse for making available at https://www.thingiverse.com/thing:3772599 and also for the model located at https://www.thingiverse.com/thing:4270682

Detailed 3D model replica of Valve Index VR headset with controllers and sensors

Remix of prittstift design. The idea is slight alteration to have part without unnecessary hole or sharp edge or stress concentration. ...The same kind of drawing rule used in aeronautical milling parts.

In the engine compartment is so much space for Frunks. Here is the first. You need 2 Spacer, 2 Screws, one M5 screw and one frunk plate. ... The Box with lid you can find here https://www.thingiverse.com/thing:6122755

This is the retaining clip used to hold the Frunk prop rod in place. Follows a similar design to the OEM clip. You can reuse the screw to hold it in place. ... Was designed by M3K.

Note the position of the tow hook storage in the image if you are uncertain.[/update] This is an insert designed to level the floor of the Tesla Model 3 frunk for using it as a container without leakage or toppings sliding to one side. I was...

A spacer that increases the height of the USB C connector on the charging cable that came with the Valve Index Controllers so you can plug it in by just putting the controller in.

A ball-joint mount for the HTC vive or valve index lighthouses designed to go in a room corner on picture rails. ... Printed in PLA on standard settings although I'm sure other settings will work.

first of all the original frunk was made by bperraud and can be found here: https://www.thingiverse.com/thing:3732284 Yes i know normally i can add it to the sources but i cant get it to work I liked this Frunk but it was missing some things i wanted...

Have rejigged the model for the Kona frunk ( possibly fit a Kia Niro too - will confirm ) to use 3mm or thicker aluminium bars to support the container which is a 30 litre plastic crate from Bunnings, Australia although any container that fits can be...

Once piece slot style mount for valve index base station 2.0's. these let you use command strips or some other form of adhesive mount for the base stations as apposed to screws. I recommend you print these vertically slot up. ...snug fit and allows...

I decided to try and think of a new way to make the stock compatible with the Valve Index, and came up with this design. I had three main purposes with this design: - Move the index controller to underneath the stock rail - Angle the controllers to...

Updated 24 FEB 2020 This contains only the parts needed to use the Valve Index with the excellent NoobTube gun stock created by Toposolitario: * Right controller grip and clamp * Grip (v2.0) allows Index with handle booster to fit * Grip (v.2.1)...

These are for Valve Index Knuckles and HTC Vive 3.0 Trackers. ... I have made two versions for flat head chargers and round head chargers (thinking about magnetic chargers for my personal use) Whatever infill is fine I would suppose, printing mine out...

Charging cable adapter fix for this model https://www.thingiverse.com/thing:3751848 The original charging cables from the Valve index are to deep and loose. I tried out an other version somebody made, but it doesn't worked. This one should be...

These are for Valve Index Knuckles and HTC Vive 3.0 Trackers. ... I have made two versions for flat head chargers and round head chargers (thinking about magnetic chargers for my personal use) Whatever infill is fine I would suppose, printing mine...