vice with clamp 3d models

... fit. So, I threw together a little spacer to make it fit my thinner desktop. I managed to make this with PLA but it was a bit laborious to get everything to snap together. ...Also used a torch to heat the end and get the Alligator clamp in.

(You can change it to a pan head by setting screw_trans to 0) support_d generates a wall to help with printing the bridge. base_thick is the thickness of the base part mount_t is the thickness of the buttresses and pipe clamp part. ...update ability to...

This clamp has been reworked from Hobby Clamps, courtesy of Rotoscan. A hole has been drilled into the rail at its base, and two small pins have been added that can be glued in place after assembly (as shown in accompanying photos). This modification...

This is a remix of the Fully 3D Printed Hinged Clamp with Source, courtesy of jdriscoll's innovative design. I've reduced the size of the screw to 5mm, introducing a functional hook for enhanced utility. ...Appreciation goes out to the original creator,...

The lower clamp, which includes an integrated z-endstop, is designed to work with the files available at http://www.thingiverse.com/download:64135. This model can be seen in action alongside http://www.thingiverse.com/thing:20382, while...

... to attach my headphones with confidence. ...As I worked on that task, I conceptualized a versatile Universal C-Clamp and multiple mounting solutions whenever they were needed. ...M5 bolts and nuts proved to be essential components in this endeavor.

Easy to use filament clamp which prevents the filament from tangling. ...Under 10 minute print.

Milling fixtures featuring a clamp lever for easy setup and adjustment.

A high-pressure container featuring a clamp is designed to accommodate three individual 8-inch membranes.

just half a turn from the clamping screw - the blade is held securely in open or closed position. update: if you have a small screw at hand, you can use the version with screw locking. no wobbling, no shifting. i always have 'respect' when i use...

I have included four stl files with a hole diameters fo the magnet of 10.0, 10.2, 10.4 and 10.6 The hole has a very slight taper (draft) so you may need to experiment with the correct size for your printer. Or print the largest one and glue the...

I have included four stl files with a hole diameters fo the magnet of 10.0, 10.2, 10.4 and 10.6 The hole has a very slight taper (draft) so you may need to experiment with the correct size for your printer. ...Or print the largest one and glue the...

In the original the back and top warped when I put clamping pressure, so I make those thicker, the headphone hanger was too short and I had trouble hanging my headphones with ease so I made it longer, my cable kept getting caught in my chair wheel so...

I needed a bumper (base) for the ICSP circuit I made on EasyEDA so I designed this.It has rounded outer corners and two notches along the inside to clamp the board down in the case so it won't move around.Don't forget to allow for legs and solder...

A larger screw and thread set provides better distribution of force over a larger area, improving the pressure applied and also the area of ​​contact with the supporting object. ...I tried to make the project as similar as possible to the initial...

The clamp can be reversed with pulling out then snapping back in reversed.PrintingThe printing directions and support needs are pictured in a PrusaSlicer screenshot. I used 3 perimeters and maybe 20% infill, printed it from PETG. I don't recommend...

Currently set as a 8 gauge wood screw. (You can change it to a pan head by setting screw_trans to 0) support_d generates a wall to help with printing the bridge. base_thick is the thickness of the base part mount_t is the thickness of the buttresses...

Make a hook a little bit longer and made a bump so the bag can't come out easy Picnic Table Clamp With Hook that can be used to hang a grocery store bag to use as garbage bag. ...Using 2 of them will work better then one. JUST A CLAMP...

I wanted to print one for my paintball gun, however, I would not have been able to use the picatinny rail mount that came with the original design. So, I quickly designed a new mount that could be attached to your barrel. What you will need: - 2...

I wanted to use it for my paintball gun but I wasn't able to use the picatinny rail mount that the other model came with so I designed a barrel clamp that allows you to attach to your paintball barrel. What you will need: - 1 1/2" flathead sheet...

This uses a 3 in clamp to secure the same bushing as the 4 " clamp previously posted. ... I had concerns that this would be too thin, so I worked up a thicker set to use the 4".

A C-clamp, also known as a G-clamp, is a versatile holding tool commonly employed in various applications such as carpentry and welding; it effectively grips wood or metal workpieces for enhanced stability during these processes.

The clamping area in this section of the press brake ensures secure gripping and shaping of materials.

A mechanical vise clamp incorporates an eccentric design, allowing for precise adjustments and secure gripping of various objects.

This is just a remix of the BASE. ...Please see the original link for the remainder of the parts. I increased the "wings" of the base to make room for these [3D printable clamps](https://www.prusaprinters.org/prints/9182-c-clamp-g-clamp-01-03/files).

Use the Thingiverse or OpenSCAD Customizer Fully parametric, compatible with the OpenSCAD customizer. ... Can set * shape of the thing being help (circle, half circle, rectangle) * breadth of the strap * size of the thing being held down *...

The print comes in four pieces - the mounting plate, the tree supports for the mounting plate, the C clamp, and the C clamp screw. You will need to attach the tree supports as a part to the mounting plate for the rail overhang. To do this in...

My software setup worked best with the .3mm clamp, but you can likely make up for differences in your own software setup. I made multiple versions anyway. EDIT: I noticed that the 1mm version was upside down, so it's been removed for now. It will be...

__Installation (Modified from the original)__ - Insert an M4 screw and an M4 nut - Slide childproof device behind doorknob - Rotate the device so that raised portion is below the lever and the lever is just barely in contact with the raised portion...

A screw is provided to prevent slipping between the clamp and support, making it simple to adjust and secure in place.