viki 2 lcd 3d models
958098 3d models found related to viki 2 lcd.thingiverse
Kossel Pro Viki 2 lcd Mount Mounts directly to the kossel pro frame. ...It sticks out a lot to clear my enclosure.
thingiverse
Here is a mount for the Panucatt Devices VIKI 2.0 LCD. The mount is designed to go on Prusa i3, utilizing one of the Z top rod mount holes. You have to drill three holes to the frame for the other bolts to go through. The LCD is mounted on a frame,...
thingiverse
A clean and simple case to house your Viki 2.0 LCD display. Print in layer height of your choice (I did it in 0.2mm) Nozzle diameter 0.4mm, extrusion width 0.4mm Print in plastic of your choice (I made mine in PLA) No supports required I printed...
thingiverse
This is an LCD bracket for the Griffin Pro1.0-2.0 with power switch relocated to the lcd rather than the side of the printer. This has not been thoroughly tested so try it at your own risk. This will require minor reworking of the power wiring...
thingiverse
Enclosure / Case for ViKi LCD on my ORD Bot. The yellow front is ABS with the rest blue being PLA all printed OK with out support. ... Instructions I think its self-explanatory but all screws our 4-40...
thingiverse
... configurations if requested. The screw tabs style was inspired by tommyc's PanelMax Vertex. Instructions BoM: 1x ViKi LCD panel 3x M5x10 SHCS 3x M5 washers 3x 2020 t-slot nuts 4x M3x16 SHCS 4x M3 washers 4x M3 nut Instructions: Bolt on and go!
thingiverse
ViKi LCD mounting bezel done in Sketchup, with a second back piece to make it a freestanding case. Use the bezel Sketchup file as a starting point for you own custom mount, or print both STL files and use together for a case. ...
thingiverse
A cover I designed for the Mini Viki LCD. I made it for my Kossel with 15mm aluminium extrusions. Check that the dial can rotate freely, you might need to shave a bit off the front circle. The arm fits both sides, just print two of them. 4x 14mm M3...
thingiverse
So after putting this off for about a half year I got around to building a case for my MakerGear M2's Viki LCD. The mounts and dimensions are based on my MakerGear M2, which was made in 2013. I know MakerGear has been continually revising their...
pinshape
So after putting this off for about a half year I got around to building a case for my MakerGear M2's Viki LCD. The mounts and dimensions are based on my MakerGear M2, which was made in 2013. I know MakerGear has been continually revising their...
thingiverse
A case for the Mini Viki LCD from Panucatt. The brackets are designed for mounting on 2020 extrusion, and are based on my earlier version (http://www.thingiverse.com/thing:1675451). There are two version of the brackets: one with a short base, which...
thingiverse
Thanks to everyone on the Makergear Google group who contributed to getting the Viki running with Marlin and Rambo. See the Makergear M2 wiki for firmware. ... Instructions Print, install using existing...
cults3d
Tips in any amount are appreciated: https://www.paypal.me/satgod use double sided tape to secure to the viki dial the center button does not require any double sided tape This makes using the VIKI LCD dial 10x easier
thingiverse
Tips in any amount are appreciated: https://www.paypal.me/satgod use double sided tape to secure to the viki dial the center button does not require any double sided tape This makes using the VIKI LCD dial 10x easier
thingiverse
... of http://www.thingiverse.com/thing:46825 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=46825 Instructions Using the following options: laenge = 35 textsize = 10 rad = 30 textshow = viki hoehe = 20 make_holder = 1
thingiverse
This mounting kit is used for Azteeg Viki LCD for Kossel Mini 3D Printer.
thingiverse
I made one of these today to use as a mockup for planning where I am going to mount it on my current printer and figured it might be useful for anyone else planning on using one of these with their Azteeg X3 controller. Full details here:...
thingiverse
Instructions I printed the LCD housing and Wire Plug with a 0.35 nozzle and hexagon pattern spacing of 2.5 mm. Side Bracket is for MakerGear M2 only. I used rectilinear support pattern of 2.5 mm. Assembly: Insert hex nuts into the wells. Put...
thingiverse
This is a mount I made for the Viki LCD controller so that it can be docked or moved to be used while sitting/standing etc. It is made to attach to 20mm t-slot extrusion. There is also a built in mount for the Azteeg X5 board which hangs on the...
thingiverse
A howto guide for getting the Viki LCD working on an M2 is on the Makergear wiki page http://makergear.wikidot.com/m2-lcd-panel. I also recommend using the M2 enclosure latch by tomlombardi http://www.thingiverse.com/thing:57440 to make sure the...
thingiverse
This Knob & button makes the VIKI display much easier to operate. It is a big improvement from the standard. Attach the knob with double back masking tape. ...The button just drops in.
thingiverse
Resized the original, which was designed for the older type ViKi panel, to take the new ViKi 2. ... Instructions Turn on support when slicing.
thingiverse
You can install this case easy after you have finish your Kossel. ...It works with clamps.
thingiverse
Customized version of https://www.thingiverse.com/thing:2482372 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2482372
thingiverse
Customized version of https://www.thingiverse.com/thing:3633456 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3633456
thingiverse
Customized version of https://www.thingiverse.com/thing:4278540 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4278540
thingiverse
Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130
thingiverse
Customized version of https://www.thingiverse.com/thing:74322 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=74322
thingiverse
Customized version of https://www.thingiverse.com/thing:4278540 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4278540