volca stand 3d models
148636 3d models found related to volca stand.thingiverse
Inspired by a Korg Volca Stand found on Thingiverse (http://www.thingiverse.com/thing:1765641), I decided to create my own Volca stand for two Volca units. It's a bit cheesy compared with the 'original' but it does the job just fine. Make sure to...
thingiverse
Stand for korg volca keys. ...Just mirror other part for set stp model for edit is attached Enjoy!
thingiverse
This is a single stand for korg volca. to print in 4 separated pieces. 2 holders and 2 stands. ...I haven't glued them so far, it is only maintain by tension.
cults3d
Stand for Korg Volca all models, by simple clipping. ...You just need to add 4 small non-slip pads in the areas provided for this purpose on the bottom.
thingiverse
Stand for a Korg Volca. Designed to stand just above a desktop synth without blocking any of the rear ports. Prints on the "back" as shown in the model and last photo. No support needed. ... More info at...
thingiverse
I made this to hold 2 Volcas. Simple design! Though you will need a 300mm printer to fit it. You can lock in the shelves with M3 screws on the ends or use glue. ... Thank you!
thingiverse
Print two of these to prop up your Korg Volca boxes. Could be used for two different angles, I guess? This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/biG3IF2qngO
thingiverse
Stand for 1 or 2 volcas that slots together w/o fasteners. ... # For one volca: Print two of stand a or b # For two volcas: Print two each of stand a, stand b, and corner
thingiverse
I made this holder, so I could free some desk space and have the Korg Volcas mounted on the wall/pegboard. It is a tight fit so it won't wobble when i play them. Update: The "arms" was a bit too long. I had forgotton my custom 3 mm feet on my...
prusaprinters
Remix of the Korg Volca stand by beejums.This simplified and slimmer version is enough to hold your Volca securely.Print 2 models and enjoy making music with a better viewing angle on your Volca ;-) 3D Printing settings...
prusaprinters
Remix of the Korg Volca stand by beejums. This version of the stand will hold 2 Korg Volcas. Additional supports/parts are not required to keep the Korg Volca's in place. Print 2 and slide onto each side of the devices. Originally printed using MG...
thingiverse
Added middle section parts TopMid, MidMid, BottomMid to be able to extend the "Korg Volca Stand 3x - Pure 3D Printed" by Fusksalad to 6 or more Volcas.
thingiverse
They either required additional hardware or were impossible to remove and made me feel like I was going to damage my volcas. There were some tweaks that could be made but I never made them because I was able to assemble it fine. For example the...
thingiverse
I wanted a stand for my Korg Volca. Found what I wanted on Thingiverse, but it was too big for my printer. This version is designed to print within a 10x10cm printer bed. Each side of the stand is in two halves, and designed to be bolted together...
thingiverse
A stand for Volca series of synthesizers by Korg. ... It's no small, and will take up space, but looks good and stylish.
cults3d
Self-contained stand for assembling two Korg Volcas of any model, by simple clipping. ...You just need to add 4 small anti-slip pads in the areas provided for this purpose on the bottom.
thingiverse
Modular Stand for 1, 2 and 3 tiers at different angles. This has currently not been tested. ...Use M5 x 25 Machine Screws and Wing nuts
thingiverse
Simple dual Korg Volca stand, requires no nuts and bolts with snap fit assembly.
thingiverse
This is a stand for the Korg Volca series mini-synthesizers. It has some cut-away area that I use to help with cable management that also saves print time. I printed two for stability. ...I am also attaching non-slip stickers cut from these: ...
prusaprinters
ENGLISH:Stand with modular elements to better organize your Korg Volca synths.There is an additional module for the Volca Modular cables that fits into the base that supports the synth.If you also own a Korg NTS-1 you can add it to the stand by...
thingiverse
For some reason, I suddenly started GASsing for a Volca Keys, although I really have enough analog synths... anyway, in my ongoing quest to fit more music stuff in my limited space, I accepted the challenge. Without a surface left, the things had to...
thingiverse
Simple solution, simple design. ... holds 2 Volcas, room to pass cable over, and through. glue spars in. ...
thingiverse
You can either use a wall adapter or you can create a simple 12V to 9V linear regulator on a small perfboard to directly power the Volcas from your Eurorack power bus (In my case i also added a simple amplifier to boost the Volca audio output to the...
thingiverse
Korg Volca Transport Box. ...Requires two neodymium cylindrical 10x5 mm magnet and some screws.https://www.youtube.com/watch?v=dONMSD41mbg
thingiverse
# Volca Case Transport case and dust protector for all Korg Volca synthesizers, made with OpenSCAD. The design can be customized. Please visit [the github page](https://github.com/mbugert/volca-case) for details, the sources and newest releases. ...
thingiverse
This is a press fit knob upgrade to give more control to the small POTs on the Korg Volca series. This is not to replace any knobs, but to press fit these over the top of the slim POTs. ...Print in clear or semitransparent material to allow the light to...
thingiverse
An enclosure for Jason Hotchkiss's awesome passive mixer, somewhat matching the Korg Volca dimensions and look. You can change the number of channels (and lid thickness etc) in the top of the scad file. The STL contains 4 channels. My build uses an...
thingiverse
A simple fix for not working KORG Volca synth (any) rubber buttons. There're many cheap conductive glues on the market, but the problem is after drying they become too rigid and easily fall off the flexible silicone. The idea of this fix is to...