voron 3d models

... VORON, I achieved a remarkable accuracy of 0.005mm with an inductive probe, while the same setup yielded dismal results of 0.1mm deltas with BLTouch. Print Settings: Printer: VORON Rafts: No No Supports: No No Resolution: 0.2 0.2 Infill: 30% 30%

Custom EVA for V6 which incorporates Voron Tap-Like probing Single 5015 SB toolboard Custom Hextrudort (mount pattern) with unlock latch, adapted motor position, gear adjustment No Insert, only Nuts for a Mercury 1-like Gantry (MGN12 on Top, 6mm...

Important: Voron Design "Cable Frame Anchor" model has been modified to make this convenient and easy to mount panel clip.&nbsp;&nbsp;Suitable for 3mm panels. Model is already properly oriented. ...Prints without supports.</p>

I developed a custom damper for the Openbuilds cube corner connectors, specifically tailored to reduce noise in my Voron project. ...The top diameter of this dampener measures 11mm, allowing it to snugly fit within the connector's opening, while its...

Tool holder for spatula and side cutter for the Voron Switchwire. It can clip with a tight fit to the side of the 3060 extrusions, or you can slide it by removing the endcap. ... I used tree support to print it.

case for HBV 5640eg Voron 2.4----BOM:&nbsp;4x M3x10 or M3x12&nbsp;2x M3x5x4 insert3x M2x4 tapping screw to mount the cam&nbsp;----&nbsp;

these handles are a mod chop up from Sturdy Handles by jeoje, they are meant to mount on the bottom frame of a voron 2.4, it help sliding, rotating, moving this heavy printer easier. ... https://mods.vorondesign.com/detail/EAM1ZiQJCUzXznvOA767w

Everybody thats got a voron knows that youre petg tube does not stays in the holder. so i created this holder What do you need? ...- print the part duh hahah - buy a PC4-M10 - Push Fitting for 4mm PTFE tubing drill the hexagon out so you can pull...

This is a remix of the Tush spool holder to hold the spool on top of the Voron 2.x printer enclosure (2mm top panel). ... BOM: 8x F695 bearings ( or similar with 5mm ID ) 4x M5x16 bolt 8x M5 washers 4x M3x8 bolts 4x T-Slot nuts

Handles for you Voron Zero Printer2 Versions, one with extra support in the middleprint the handles laying on the printbed, and fasten them to the printer using m3 nuts (slide them into the extrusion from the front or back)

... holiday. ...Prints with no supports. Insert the hook hanger and use a piece of 1.75 filament to lock the hook into place from the rear.  I hope you guys enjoy them as much as I enjoyed making them. Featured in the 12 days of voranmas with Voron Design

It all holds and fits together nicely.To print right panels, simply mirror objects in slicer.Dimensions are adjusted to work in 0.2 mm increments.Since prints are pretty big, ensure your bed adhesion is good to avoid warping.Alternatively, print on...

**Disclaimer: If you *can* get the right frame, you should.** If like me, you ordered a "Voron 2.4" frame from aliexpress and it came with V wedges - or if you can't take delivery of Misumi frames in your region, these might help. The biggest...

This is a remix of the stealth burner V6 mod for the Voron printer. Its now capable of taking the V6 fin-stack with a volcano hot end. This is to replace the stock afterburner. Must be printed in ABS, with 4 parameters and 40% (gyroid or...

This is a cooling solution for the Voron V0.1 for high-speed printing. The air duct can be printed either from PETG / ABS or ASA. The tool head should be printed with at least 30% infill. ... ASA / ABS is the best choice here

This thing matches up perfectly with Vorons Version 1.5/1.55 compatibility. Simply swap out the cable harness for the Printhead-Chain-Adapter, which not only lets you connect the cable chain but also comes with a handy little storage compartment for...

If needed , feel free to adjust the hole and pin size of it.Mounted infront of the Voron Afterburner tool head using the same M3 of the fan casing. Printing SpecificationsMaterial PETG Prusament Galaxy Black (See also Prusament recommendation)LH: 0,2...

Quereinbau des Fysetc Spider Mainboards, dadurch bessere Kühlung der Steper-Driver 2x pcb_din_clip_x3.stl aus dem Voron-Github 4x Einschmelzmuttern 4x die Schrauben fürs befestigen der Clips M2x 8 bzw 10 selbstschneidend. 4x M3 Clips bei der...

If you can find a AdamTec IEC-GS-1-100 Inlet and want to use a generic C14 IEC socket for the Voron Legacy, you may have trouble with how shallow the housing is. ...So, I have made a shim that should stop your mains crimps from getting bent when...

---------------------------------------------------------- Panel clamps for Voron ===================== Unfortunately, the Voron's panels aren't factored into the rigidity of the construction, they're just meant to provide an enclosure for the...

It can clip with a tight fit to the side of the 3060 extrusions, or you can slide it by removing the endcap. I used tree support to print it. Print Settings Printer: Voron Switchwire Rafts: No Supports: Yes Resolution: 200 Infill: 15 Filament:...

By getting this product fitted to your VORON machine, you will get a nozzle cleaning function. ... Method of operation: Drive the machine to brush the cleaning brush before printing by modifying the slicing software script, using the VORON R2 as an...

Spidey is enveloped by Voron’s disabling energy web!! But wait, it looks like he is managing an escape! Whew!!! That was close, Spider-Man. Too close. Good thing Peter Parker managed to get a 3D hologram just as you broke that energy web so we could...

... in your slicer. BOM (per panel): 16x M3 Socket screws - 6mm 72x 6*3 round button magnets 16x M3 2020 Series T-Nuts Print Settings Printer: Voron 2.4 Rafts: No Supports: No Resolution: 200 Infill: 13 Filament: KVP ABS Black Category: 3D Printer Parts

This mod adds a PG9 cable gland to the Voron 0 back panel, and reuses the Dragon groove mount adapter for the bowden tub.You need to print:bowden_clip_x1.stlEither:panel_nonsplit.stlpanel_a_x1.stl &amp; panel_b_x1.stlIn addition, you'll also need:1...

will need some 5x4 3m inserts, same ones that come with the voron 0.2 kits, as you need them for the two hole on the LEDs strip, well the thing just pushed down, so you would need to get access to the ends so you cam do this anyways, thought to make...

Hi again guys!!!I have encountered the problem with the original bumper when using it with the Fysetc CNC X carriage and that's why I made this remix to solve the problem The print is straightforward and can use the exact configuration from the Voron...

This is an upgraded PSU holder for Voron 1.5 that offers a cost-effective solution by utilizing affordable Chinese-made SSRs (Fotek SSR-40DA). The design provides an additional 10 mm of clearance, making it easier to manage wiring. ...Specifically...

VORON - C270 HolderFor mounting bottom side gantry&nbsp;→ C270_holder.stlor for mounting on the frame→ C270_holder_large.stl&nbsp;BOM:2x M3 Threaded Insert1x M3x81x M3x20&nbsp;Remix:https://www.thingiverse.com/thing:4742899&nbsp;&nbsp;&nbsp;

The kit is mainly used to increase the cooling effect of the product when the VORON machine prints, with 24V 12032 large blower as an auxiliary cooling fan, which can provide strong wind power, greatly increasing its cooling effect, providing more...