voron 3d models
3554 3d models found related to voron.
thingiverse
Echter HEPA Filter für Voron 2.4 oder andere Drucker / True HEPA filter for Voron 2.4 or other printers =========================================== ### Deutsche Version: Ich musste lachen, als ich meinen Voron zusammengebaut wurde und von einem HEPA...
thingiverse
Updated to v1.1 Magnetic ADXL accelerometer mount for the stock Voron Afterburner. Neodymium magnets are positioned to match the front Afterburner screws. Obviously the Afterburner screws need to be a ferrous type metal for this to work so if...
prusaprinters
Trident PTFE GuidesPrinting:Default voron settings, correct orientation, no supports needed!Bom:Only printed parts.Description:Made to guide the PTFE tube uniformly into the extruder, and avoid rubbing against the top panel.One 90° version and one...
thingiverse
Install the proper Voron font from here - https://fonts.google.com/specimen/Play?preview.text_type=custom . On Linux you can just move the .ttf file under /usr/share/fonts On Windows you can install it by just extracting the zip, and then opening...
prusaprinters
I printed it with no supports (Voron logo side on the print bed), but be aware that some of the overhang is steeper than 45 degrees, especially around the screw holes.The Hose connector is printed with the locking tangs facing down. I integrated...
prusaprinters
This is a simple printable 2 part deck panel for the Voron Switchwire. I've added 3 additional mounting holes to better align the panels, and more rigidly mount them. The panel is split in 2 parts that just fit on the VSW build plate.</p><p>I'm...
prusaprinters
(PS, the `out` port wire on the left RGB board needs to be plugged into the 4pin xh2.54mm Male connector)connect to the motherboard and check all the wire sequences of xh2.54mm connectors Bomv0-Umbilical x1M3x6 BHCS x8-12NeoPixel 8 x WS2812 5050...
prusaprinters
If you are trying to do the single door mod this may not be good enough for that since I worked the holding out with the voron 2.4 350 door in mind. Also note these do have the door panel sit flat against the face of the frame.Hardware:M3 x 8mm and...
thingiverse
# Update 04/10/2021 ## pre-support files # added mount for NF-Crazy Volcano (Let's push it further ) NF Zone-Volcano https://fr.aliexpress.com/item/1005001664990482.html ## update 27/09/2021 - add adjustable slot on the backplate for controlling...
thingiverse
This is a generic ADXL345 mount for the Voron Afterburner toolhead. It uses the two lower hotend fan housing M3 bolt locations to attach the mount and gets the sensor close to the nozzle. To install the chip to the mount use two M2x10 or M2x12...
thingiverse
I adapted the Voron Afterburners to fir the Weedo X40 IDEX printer. ... These are designed to fit any V6 type hotend Required hardware: 4 x 8x3 round magnets ...
prusaprinters
These Cooling ducts where designed to keep the XY motors on my voron 0.1 cool when i turn up the current. At the moment my motors run at 0.8A but i also experimented with 0.9-1A. Maybe will go even higher once i got some spares for...
cults3d
Voron Zero (V0VO) toolhead Dragon / Mosquito Based on HeVort extruder( By MirageC with Big thanks to Him on this awsome design ) How to print supported parts to VOV0 tool-headhttps://www.youtube.com/watch?v=CkwsMm29IuA Video assembly ! ! BOM BMG...
thingiverse
... the screws and secure the entire assembly to the motor. Align the key on the motor with the slit, slip on and align the MK8 drive gear, and finally tighten it. Print Settings: Printer: VORON Rafts: No Supports: No Resolution: 0.2mm Infill: 40%
prusaprinters
I doubled the magnets for the midspan clips, as the panels can sometimes bow out in the middle. For a Voron 2.4 or Trident, assuming you only intend to do the sides and top, you will need the following:12ea, corner clips12ea, midspan clips4ea, 4mm...
prusaprinters
I wanted removeable hinges for my voron panels that didnt require any modification to the panels. So I combined Alexander T. Moss's brilliant clamping hinge idea with this amazing removable doors mod by ElPoPo. I just swapped the hinge attachment...
thingiverse
This is a Logitech c920 mount for the Voron V2.4 (may work on other Voron Designs).
prusaprinters
Using the buffer as my ERCF buffer for my voron and wanted the Voron Logo. I ended up stacking 3 together with some glue. ... </p>
thingiverse
Simple remix of the Voron M4 Guidler to add identification of your extruder.