vortex tripod adapter 3d models

I adapt this converter to suit my personal stand 27x27mm.

This thing is designed to slip tightly over the rubber feet of these tripods:...

Kinect adapter for tripod solidex and similar brands.

To add extra stability and prevent damage from friction or movement, consider adding two pads made from rubber or cork between the tripod and the mounting plate. Print Settings: Rafts are disabled by design for streamlined printing experiences. ...

I needed a way to securely attach my Spiffy Lumiee lights to a small tripod while taking photos, as no suitable accessories were available from the manufacturer. Since no solution could be found, I decided to design one myself. In addition to...

Originally designed to add an iPad-based teleprompter to my tripod with a 1" shaft. Requires a 3/32" roll pin at least 1" long for the pivot point. Two 1/4-20 jam nuts are required: one for the knob and one for your attachments. A single, 1/4-20 x 2"...

Plate for a Star Fluid tripod\n10-29-14 Created a new version without any marks\n \n \n Directions Fused 100% of the material using an ABS filament at 230 degrees Celsius.\nThe heated platform was set to 110 degrees Celsius.\nThe printer produced .2...

... custom fitting. Initially, attach the piece with the jam nut to Kinect, followed by sliding the other piece onto it. Align the holes and fasten with a tripod bolt to complete assembly. ...Note that the cord notch may require cleaning post-printing.

'If only I could link my laser measurer to my tripod I could fire the beam then take the level while grasping the staff.' So this attaches to a standard surveyor's tripod (5/8 11 TPI). The footplate attaches to the bottom of my laser measurer and...

I've tested it with my 5.41 inches HTC One mobile phone and 2 different tripods - it works flawlessly. Note : I'd recommend to put your mobile phone horizontally in it, but if you need to turn it vertically, then I've added some vertical guides at...

'If only I could attach my laser measurer to my tripod, I could fire the beam then take the level while holding the staff.' So this attaches to a standard surveyor's tripod (5/8 11 TPI). The footplate attaches to the bottom of my laser measurer and...

... the design again. I stumbled upon a tripod screw on Thingiverse and printed a dozen of them. Took about an hour, Fit in my thread was perfect, and a plastic screw to lock in the phone is best - in my opinion. Have a fantastic day! ...PeteTheShopper

remix from orginal http://www.thingiverse.com/thing:2228225 my modifications: - the adpater is now 43mm by 43mm to fit my tripod mount - the height is a bit bigger to fit S8Plus As in original: printed with no infill and no bottom/top layers; 0.3 mm...

Adapter Mount for Swing Arm Desk Lamp Suits Arca-Swiss Ballhead. ... Designed to Accommodate Lamps with 13mm Post Diameter.

A snap in tripod mount. Printed with PETG, layer 0,35mm. ...The thread is also printed but not perfect, so screw it carefully for the first time (may be tighter), but then should work well.

Here's an easy way to attach your Duo5800 to a tripod: simply snap it in and out! Team High Society designed it that way. Check out their YouTube video here: https://www.youtube.com/watch?v=8A1i7-R8MSE. You can also find more of their content on...

We needed to be able to mount them to tripods. So I designed this part to make to the security camera mount and insert a 1/4-20 threaded insert into the middle.A true plastic heat insert for plastic turned out to be quite expensive compared to the...

I'm attempting to design a basic JeVois camera module mounting plate that fits standard tripods and 1/4" UNC bolt attachments. I drew inspiration from the official documentation at http://jevois.org/doc/CaseMounting.html, which specifies that the...

Human: Simple adapter for attaching a swing arm desk lamp to an Arca-Swiss compatible ballhead. ...The opening accommodates lamps with 13mm diameter posts.

... ballhead, designed to accommodate lamps with a 13mm diameter post. ...Eustathios's printer is the perfect choice for printing this adapter, which can be paired with various filaments found on thrinter.com, including eSun Transparent Magenta PETG.

I bought a GoPro frame without said adapter so I made one. ...Print the adapter at about .12 to .15mm layer height so the thread turns out well. ...You will need a M5 bolt (at least 30mm long) and a M5 nut.

Hey guy today I bring you a super simple yet really effective adapter for the SnowBall mic. I printed it with an infill of 50%. Subscribe to MrJefferson105. Print Settings are as follows: Printer Brand is Prusa, and specifically I used my Prusa Steel...

Small adapter designed specifically for phones measuring between 58mm and 75mm wide. Large adapter available for cellphones that are 70mm or wider in width. Printing with no support is recommended. A layer height of 0.2mm is ideal, along with an...

Adapter is made to fit the Modular Mounting System which you can find on Thingiverse.https://www.thingiverse.com/thing:2194278To bind the two pieces together you can use glue or (as I did) use a solderingiron to melt the pieces together.

Adapter is made to fit the Modular Mounting System which you can find on Thingiverse.https://www.thingiverse.com/thing:2194278To bind the two pieces together you can use glue or (as I did) use a solderingiron to melt the pieces together. 

Patreon: http://www.patreon.com/flowalistik Donations: http://www.paypal.me/flowalistik Smartphone adapter to use it with my phone and record timelapses. https://youtu.be/nDVSt6vrTy4 The model from the pictures was printed with no infill or...

I'm using my trusty Logitech HD Webcam C310 with an adaptable Quick Grip. The clamp that's working like a charm for me is the one-handed mini bar clamp from Irwin, which I found at https://www.irwin.com/tools/clamps/one-handed-mini-bar-clamps/. ...

The pictures showing the adapter with iPhone 4S (the parts for iphone 5 & 6 are not tested) Dimensions and other parts available on:http://www.genapart.com/blog/ressources/ Holder for iPhone 4 & 4S => Support_iPhone_4.st Clamp for iPhone 4 & 4S =>...

This adapter allows Tento 20x60 binoculars to be mounted to a Manfrotto/Bogen RC2 quick release clamp. I suspect it might also fit the Kronos 20x60, but I don't have one to test.eSun PLA+0.15mm layers6 perimeters60% grid infillThe main part should be...

The pictures on my computer show the adapter paired with an iPhone 4S, but I haven't tested the parts yet for iPhones 5 and 6. To learn more about the dimensions and other hardware needed to build this holder, you can check out my blog at...