voxelab proxima 3d

This design will create more room on your bench top. It combines a tool holder, a SD card adapter and relocates the control panel to be closer to the center line of the printer. The tool holder, can hold all the tools that come with the Aquila, plus...

supportless

This is a remix of TontoTraveler's psu cover (https://www.thingiverse.com/thing:4972200) Instead of the original cord mount I switched it with a cable chain mount. Included the chain links and bed corner cover. the bed chain has 18 links. ... ...

This mount uses heat-set inserts instead of nuts. ... Needs 2x 16-20mm m3 screw, 2x 6-8mm m3 screw,2 m3 heatset inserts.#define NOZZLE_TO_PROBE_OFFSET {​ -42.2, -8.7, 0 }​

This modification moves your X-Axis end stop back 7.5mm, allowing for access to the complete bed width of 235mm instead of just the 220.

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

This is a direct drive extruder designed to use stock wiring so there is no need to purchase any cable extensions. The x-axis needs to be printed with tree supports. Keep the screws when removing the x-axis cover as you will reuse these same...

remixed the satsana uploaded by JeremyLawliet, the lower fan ducts had interference with some printed parts so i gave them more clearance hopefully no more touching prints. ...i also removed the bltouch mount as ill never use this feature and its just...

Allows you to use the full 235mm of your x axis vs 220 as stock. Changed from the original I moved up the 4mm bolt holes by 1/2mm each side so you dont have to stretch the model to fit. I also enlarged the endstop board holes so theres less...

This remix performs the following changes: 1. Reinforce the mounting bracket to prevent splitting when attaching the bracket to the printer 2. Enlarge the mounting bracket hole. ...Previous version did not fit on my Aquila as the bracket would hit the...

Adjustable angle vertical screen mount for the Aquila, some fan shrouds might hit the screen depending the angle you select, make sure to check first...

The Aquila has a slightly different carriage plate than the Ender 3 V2, and I needed a more accurate model than I've been able to find. The "face only" model is easily and quickly printable for comparing the mounting face of this model against a real...

This will allow you to mount a CR Touch to your Aquila printer. It has a opening to allow for the connector to the CR Touch. I designed this part in Fusion 360 and sliced it using Cura 4.7.1. ... Printing: layer height .2 mm skin 3 layers ...

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

Made to improve the angle of the filament as it's fed. There's another filament guide that's really popular, but I decided to make this since it's way simpler, doesn't require total accuracy, and doesn't require bridging. ... Here's the Onshape link:...

simple remix of Earthmann's fan housing for the ender 3 v2. i also doubled the thickness cause i thought it was a bit flimsy. you can use 24v 80mm fan without a buck converter. i found these fans still pretty loud so i switched to the 12v fans with a...

same as the original remake, just with a uniform top layer and no USB holder protruding

Designed this in fusion360 (file included) to extend the switch so when my printer homes using the Creality sprite extruder, it's actually over the surface instead of the edge. ... It will need to be glued to the inside, then screws to secure it...

Just a small addition adding an Aquila. may the Emperor guide your prints! ...

After changing to a clone BMG Extruder I couldn't find any mounts that worked with it. So after a few iterations I came up with my own. I cut a small piece of PTFE tubing down to fit snuggly between the extruder and the runout sensor to make...

The stock spool holder was too high; didn't fit on my shelf. This one is lower, you lose a bit of z height but that doesn't matter to me much. Also this has lower rolling resistance than the stock holder. The tube is a piece of PTFE filament tube...

This is a Support Arm for the Filament Holder, when you use Madgutts relocation bracket. https://www.thingiverse.com/thing:4842319 This will fit the build plate but does take most of it up. I printed with PETG using a brim on the glass plate. I...

<p>make sure your bed is clean before using it!!<br>print in PLA using support&nbsp;<br>you can freehand level your bed or use the g-code &nbsp;(it will move the hotend to 4 corners)</p><p>demo video&nbsp;<br>&nbsp;</p><figure class="media"><oembed...

If you have this upgrade printhead (https://www.thingiverse.com/thing:3179892) you have the following problem. When leveling the bed with the BLtouch sensor, with the air channels in collision with the display. Thus, I have constructed a spacer for...

Satsana shroud for the Aquilawith a mount for 5015 blower fan. ...This is the raised version with BLTouch and without the "Aquila" script across the front.

Remixed from the Ender squash ball feet, the Aquila has a metal plate on the bottom which covers the electronics but prevents the feet from attaching correctly in the back. This remix adds a small cutout on the bottom to add clearance for the plate.

Used 2 items that I thought would be cool together. Credit goes to squidward715 and Strange_Creations I just mashed them. ...

Made an adapter to attach to hot end enclosure to guide the filament directly from the extruder to the hot end. 2/17/22 Made a change! First model was a little off. ...

This is a fan duct design based off both the Satsana 5015 Remix, along with my Longer LK5 Pro Fan Duct design. It's very, very similar with the LK5 Pro design, but the mounting is different. I'm not a fan of the sparse mounting options for anything...