wall sword hanger 3d models
264176 3d models found related to wall sword hanger.
thingiverse
I had to mount a gifted Master Sword on the wall so I made this wall hanger model. ... After printing it with "gold" coloured PLA, I wasn't satisfied and coated it with gold spray polish.
cults3d
I had to mount a gifted Master Sword on the wall so I made this wall hanger model. ...After printing it with "gold" coloured PLA, I wasn't satisfied and coated it with gold spray polish.
prusaprinters
I wanted to make a simple vertical wall hanger for the amazing Master Sword Model from Popandsicle.Not nearly as beautiful designed as the Master Sword, but it does what it was supposed to do ;PI printed it in Wood PLA from GeeetechLayer height:...
thingiverse
This is a hanger I made for my Excalibur sword. It can fit a lot of large swords and it is strong enough for their weight. ...It uses four screws.
cults3d
This is a single sword wall holder from my 3 sword holder design. ...Haven't printed one yet, but I don't see why this one wont work the same.
myminifactory
... My particular swords have a rather large diameter hilt, so I had to move them away from the wall a bit. Pay no attention to the unfinished wall in the photos. ...That was the previous occupants "handiwork." I'll get around to repairing that later.
cults3d
... My particular swords have a rather large diameter hilt, so I had to move them away from the wall a bit. Pay no attention to the unfinished wall in the photos. ...That was the previous occupants "handiwork." I'll get around to repairing that later.
thingiverse
... My particular swords have a rather large diameter hilt, so I had to move them away from the wall a bit. Pay no attention to the unfinished wall in the photos. ...That was the previous occupants "handiwork." I'll get around to repairing that later.
prusaprinters
My particular swords have a rather large diameter hilt, so I had to move them away from the wall a bit. Pay no attention to the unfinished wall in the photos. ...That was the previous occupants "handiwork." I'll get around to repairing that later.</p>...
pinshape
My particular swords have a rather large diameter hilt, so I had to move them away from the wall a bit. Pay no attention to the unfinished wall in the photos. ...That was the previous occupants "handiwork." I'll get around to repairing that later. ...
cults3d
Print two for both sides of the sword use at your own risk (make sure the sword isn't to heavy) and obviously use proper screws
thingiverse
I printed the Inquisitor Sword from Warhammer 40k by Teptec from pinshape, I needed a way to store it, so i increased the size of the sword hanger and added in an aquila eagle and combined them with a block in Tinkercad.
thingiverse
Simple wall mount for displaying knives designed for Neodymium bar magnets of 60 x 10 x 3 mm which I purchased from Amazon. Superglued the magnets in place. Multiple mounts could support larger knives or swords. ...
prusaprinters
I printed the Inquisitor Sword from Warhammer 40k by Teptec from pinshape, I needed a way to store it, so i increased the size of the sword hanger and added in an aquila eagle and combined them with a block in Tinkercad. Print Settings Printer...
cults3d
for when you have swords and need to hang them .... ... :-) If you like my models please consider supporting me on Patreon : https://www.patreon.com/bigmrtong
thingiverse
for when you have swords and need to hang them .... ... :-) If you like my models please consider supporting me on Patreon : https://www.patreon.com/bigmrtong
thingiverse
Wall hangers to place two swords of similar guard height parallel on the wall with simple fasteners. ... One set is higher to allow the swords to cross without touching or bending.
thingiverse
I'm making Narsil for myself and needed a way to hang it on my wall so I created this thing. I used https://www.thingiverse.com/thing:685824 from NathanSquire67 for the tree. ... Screw holes are 3mm diameter.
thingiverse
This goes with the Golden Sword for Finn I made. The model I uploaded for the sword is designed for a kid. I enlarged it myself in Tinkercad to make it a bit bigger. If you do the same, this will work for both sizes. The arms are not perfect. I'm...
thingiverse
A wall hanger for the Zelda Sword and Shield from World of Nintendo so you can properly hang them without removing any zip tie.
thingiverse
I failed to insert a folded notecard to tighten the shield and holder, so I will probably work on making the handle part of the wall hanger tighter in my design. *** *Update 1*: I finally stopped being lazy and updated the hangar. It grips the...
thingiverse
This is a hanger for my son's replica (Skyward Sword) Master Sword. It's designed in Tinkercad to hold it by the lip of the top ring of the scabbard. If you've bought one of these costume/Cosplay props this may be useful for you between adventures....