wanhao duplicator 4s z axis brace and bushing 3d models

Print Settings Printer: Maker Select (Wanhao Duplicator i3) Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 2 mm Infill: 10% Notes: The resolution and infill probably won't make a huge difference; I just chose 2 mm since these don't need...

Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: No Supports: No Resolution: 0.2mm Infill: 25% Notes: Simple print, place the object flat on the build platform and start printing. No support needed; it...

3D printer bracing for z-axis. Makes the printer more sturdy, and eliminates some vibration and movement while printing. I designed these to be small, and easy to take on and off if needed. These work really well, and they also make the printer look...

This initial design for a Z-Axis Brace still requires testing. If you test it and share your feedback, I can finalize this model. Print Settings: Printer Brand: RepRap Printer: Hictop Prusa i3 Aluminium Rafts: No Supports: No Resolution: .3...

... Please note that these jigs are specifically designed to work with the z-axis brace found on Thingiverse (https://www.thingiverse.com/thing:921948). ...If your z-braces have felt feet or you don't use the z-brace, these jigs will not be effective.

Print Settings for Qidi Tech I Printer: Printer Type: Qidi Z Axis Guide Rods Stiffened Up for Optimal Performance Rafting Option: Disabled Support Structure: Removed for Smooth Print Finish Resolution Setting: Set to 0.3mm for Precise Prints Infill...

Upgraded to dual x axis stepper motors and needed to increase frame height due to direct drive so I made these. They increase frame size by 20mm. ...They have a recess for the bearing and bearing cover that came with the upgrade kit I purchased.

Upgraded to dual x axis stepper motors and needed to increase frame height due to direct drive so I made these. They increase frame size by 20mm. ...They have a recess for the bearing and bearing cover that came with the upgrade kit I purchased.

You'll also need two right and two left POSA5 SA5T/K 5mm Male Metric Threaded Rod End Joint Bearing M5x0.8mm rod ends. In addition, get four right-handed M5 nuts and four left-handed M5 nuts. ... This design was created with Tinkercad - Edit it online...

Prints with no supports. You'll also need 2 right and two left of these - POSA5 SA5T/K 5mm Male Metric Threaded Rod End Joint Bearing M5x0.8mm As well as 4 right-handed M5 nuts and 4 left-handed M5 nuts. This thing was made with Tinkercad. ...Edit it...

Simple mount for Z-Axis ACME bushings with 4 holes, 22mm diameter disk. ... Outer mount holes designed for JG-Maker Artist-D Pro, will probably work for other models.

This Simple Brass Bushing Holder Serves As A Trusty Sidekick For An Ultimaker-Style Z Axis. ...It Was Conceived Using Tinkercad's Versatile Tools, Allowing For Seamless Online Editing Through https://www.tinkercad.com/things/4Hg6T3h9p7A

This one is for M10 575mm threaded rod (length can vary by+/- 5mm) You need additionally M10 nuts and washers. All other screws remain original. I made all parts a little bit more stable. For the top ones this means, you need support for the...

I came up with this design to integrate a Z axis brace and enclosure frame into the one bolt up mod. The frame is designed to take a 3mm PMMA half enclosure for the front of the printer, helping to stabilize temperatures for ABS printing. This rear...

Advanced users prepare to modify the Very Big Z braces for the Wanhao Duplicator i3, Cocoon Create, Maker Select, and Malyan M150 i3 3D printers. This modification is intended for experienced individuals only. ...I strongly advise against attempting...

Based on this mod: https://www.thingiverse.com/thing:4756659 Does not decrease the height along the Z axis and has technological holes for extracting magnets. ... You will need the following parts: Magnets: 5x1.8mm - 8pc 3mm ball - 4pc (if your...

WANHAO DUPLICATOR D9 X-AXIS TENSIONER Additional requirements include: * Four Allen bolt hex sockets, size M3, length 50mm, to reinforce connections between layers.

... it. The x-axis should be positioned at a lower level than usual. Print Settings: Printer: Wanhao Duplicator i3 Rafts: No Supports: No Resolution: 0.2 Layer Infill: 50% Notes: I am printing with three shells and five or more solid top/bottom layers.

Adjustable Z endstop raisers are available for the Wanhao Duplicator i3, often required when installing a glass build platform. ...To secure it in place, obtain two extra M2 screws and corresponding low-profile M2 nuts.

Anti-Wobble Solution for WanHao Duplicator and Malyan M150 Printers: Printing at 0.2mm Without Support

Wanhao Duplicator i3 z-rod stabiliser you going to need 2x 16mm linear ABS bearings 2x m4-25 bolts 2x m4 nuts

Drill out the limiter switch holes to accommodate them properly. ...The z-brace will not move without its limiter stops functioning correctly.

I encountered considerable wobbling issues with my Wanhao Duplicator i3. ...The problem lay with the connections of the X-axis rods, which I remedied by printing additional supports as clearly evident in the accompanying photographs.\r\n\r\nPlease note...

A Simple Camera Mount for Wanhao Duplicator i3 with Z Brace Mod. Since HillbillyZT's mount wouldn't work with the Z brace mod, I designed my own. This camera mount is compatible with any camera featuring a standard 1/4" tripod mount, but it was...

A simple camera mount for a Wanhao Duplicator i3 that has the Z brace mod installed. HillbillyZT's mount wouldn't work with the Z brace mod, so I designed my own. This is compatible with any camera that has a standard 1/4" tripod mount, but I...

I designed a simple camera mount for my Wanhao Duplicator i3 with Z brace mod installed because HillbillyZT's mount wouldn't work with the Z brace modification. I came up with my own design. This mount is compatible with any standard 1/4"...

You can fiddle around doing all the z-axis bracing later; there are countless tutorials on how to do that. The next problem is that the heated bed won't get to 90 degrees C without modding the drive voltage. Luckily this is simple and takes about 5...

M5X8MM HEX SOCKET HEAD FLAT COUNTERSUNK ALLEN SCREW INSTRUCTIONS FOR THE WANHAO DUPLICATOR D9 Y AXIS TENSIONER To strengthen the connection between layers, you need to install screws in the file "y axis screw tensioner + bracket". This file contains...

Following the lead of FilamentCorner's z Brace and z Extensions (Z-Kit), I decided to make a hybrid design that moved the braces to the back of the printer so as to be out of the way. All of this is based on AzzA's original work which can be found...

You will need the following parts to complete your Wanhao Duplicator D9 X Axis Motor Bracket: This bracket design allows the motor to be securely attached to the X-axis of your 3D printer. To ensure a solid and durable attachment, you'll need to...