wemos esp32 3d models

The firmware and Gerber files for the PCB are available here: https://github.com/reivaxy/iotFeeder, but you can probably fit an ESP8266 wemos D1-mini board + stepper driver board instead, but don't power the stepper driver from the ESP 5V pin, you...

I've opted for using an 18650 battery to power the Arduino code on either a Wemos or NodeMCU board inside the sphere. There's also space for a micro USB port to charge the battery via a small charger I ordered from AliExpress. Currently, this...

I was looking for a straightforward, tough keychain case to haul around a Wemos D1 Mini board. After spending a Saturday afternoon messing around in TinkerCAD and test printing, I finally came up with this. It's not fancy. It has decent clearance...

The firmware and Gerber files for the PCB are available here: https://github.com/reivaxy/iotFeeder, but you can probably fit an ESP8266 wemos D1-mini board + stepper driver board instead, but don't power the stepper driver from the ESP 5V pin, you...

This is the case of my portable tiny ZX Spectrum 48K (emulator) using a Wemos Mini :) Has a fully functional 40-key qwerty keyboard just like the real one, so it's fully programmable just like the real one too, as well as run virtually any game made...

https://youtu.be/3oBN2pKksdo Wemos D1 Mini: https://amzn.to/2TEORFx Strip Led: https://amzn.to/2I13hP2 Leds individuelles: https://www.banggood.com/custlink/GGvGy84E7G Condensateurs: https://amzn.to/2SjiZcM or...

I had a WS2812 led strip, as well a battery and a wemos lying around, so i thought about making a rechargeable luminous bunny with WLED.First i tried to change the existing base design, but ended up to completely remake the base and also fixing the...

Full instructions for this project can be found under the regular version: https://www.thingiverse.com/thing:3354082...

The lower part has been adapted for the USB-C version of the ESP8266 WeMos D1 Mini. 3. Adapted for the NRF24L01+ with external Hardware I used for this: - ESP8266 USB-C - NRF24L01+ with external - 0.96 inch OLED display SSD1306 128x64 ...

* Here's a manual for the external antenna mod: https://forum.pimatic.org/topic/2618/greater-wi-fi-area-for-esp8266-01-with-external-antenna * The 4 screws are 2.9x9mm Shopping list: *...

The programmer works seamlessly with the Arduino IDE to program the target board just like Wemos and Node MCU development boards do. My goal here was to make it possible for the target board to function solely with a 6-pin header for an external...

Controlled by a Wemos microcontroller running NodeMCU Lua, this setup utilizes a modified inductive heater circuit for the primary. ...Take a closer look at how it's done: https://www.youtube.com/watch?v=a7RZmR6kDDs And if you're looking to make some...

This is the casing for the Wemos D1 Mini CH340G breakout, a stripped-down version of the board with the ESP12 module removed to use as a programmer for bare ESP12 modules. The result is a labelled module that stacks neatly, providing a ready-made...

This is the case of my portable tiny ZX Spectrum 48K (emulator) using a Wemos Mini :) Has a fully functional 40-key qwerty keyboard just like the real one, so it's fully programmable just like the real one too, as well as run virtually any game made...

let me know if this works..Case to hold a Wemos D1 mini and JSN-SR04T ultrasonic distance measuring sensorI use with ESPHome and Home Assistant it to measure the level of a 1000l diesel tank.Now screws required.The lid is a snap-fit connectionThe...

The CNCshield has a Wemos D1 board underneath it, which is an ESP8266 WiFi module. This will be used to replace the Arduino UNO in the 4xiDraw (http://www.thingiverse.com/thing:1444216). The code includes a trapezoidal speed profile like GRBL. The...

This is the casing for the Wemos D1 Mini custom shield, an RFTXRX (RF Transmitter/Receiver). The D1M block has a breakout for 433/315 MHz units, specifically the MX-05V and MX-FS-03V. Other units may work as long as pin assignment and power...

use the following config with ESP home and wemos d1 mini. ...Reference the attached curcuit ```yml sensor: - platform: adc id: source_sensor name: "position sensor" update_interval: 1s pin: A0 filters: - multiply:...

This is the casing for the Wemos D1 Mini (custom shield) GY521 (Gyroscope/Accelerometer). This D1M Block connects power and I2C pins. The address and interrupt pins can be easily connected as needed. The following components are required for this...

I designed it to house an ESP8266 however it should fit other microcontrollers such as Arduino Nano or ESP Wemos D1 with some room to spare for a simple transistor or resistor/LED circuit. My intention is to control the air freshener via my home...

so page has an aux(drone)light option to activate drop ) Parts: SG90 Micro Servo Wemos d1 Mini Pro, i used pro for the ext aerial but reg D1 mini still has some distance Need a metal T-bar (3mm channel) - was going to use earring bar or can cut down...

Hi, Originally started as an enclosure for the beautiful NTP clock made by W8BH http://w8bh.net/NTP_DualClock.pdf but of course useable for anything in need of a 2.2" SPI LCD TFT Display and a Wemos D1 mini. As shown in the pictures, the D1 mini...

Parts needed: - Wemos D1 Mini - CO² Sensor MH-z19 - LED Ring 12 x WS 2818 or similar (inner diameter of at least 35mm and outer diameter of maximum 54mm) - 30mm x 30mm fan, 5 V Make sure to burn in the CO² sensor when using it for the first time. ...

Wemos D1 Mini and a USB lead. A connection board, either a prototype strip board or the specific one from http://ebay.us/PeYuHQ. Some demo firmware for the display can be found at https://github.com/Mottramlabs/MAX7219-Dot-Matrix-90-Degree-Demo. ... To...

In my video linked here I show how to build a transmitter with an ESP8266, like the Wemos D1 mini and a RF module, to control awnings and shutters using the Somfy RTS remote controls. And here is the case I designed for this purpose. ...It also has...

A spacious compartment beneath houses a WeMos D1 Mini, while the sphere's ample interior accommodates multiple RGB LEDs or a vibrant LED ring. A convenient USB port resides at the base, accessible via a neatly concealed slot that securely clamps in...

To get started, you'll need: - 1x Wemos D1 mini, which is highly recommended, but other ESP8266 variants can also work with an additional step-down converter. - A WS2812b led strip, ensuring a high IP rating, such as IP30. It's essential to choose a...

This bracket supports the Brew Bubbles project.The bracket is intended to position the Wemos D1 Mini and shield with photo-interrupter such that the bubbles in the airlock will register and be counted. The hole may need to be adjusted larger or...

The ESP-12E WeMos D1 WiFi uno board will connect to your router using Wi-Fi. Adafruit Motor Shield v2 is the perfect match for this setup. To control everything, we recommend using ESPeasy. For a 15 - 20cm wall installation, you'll need some...

The illumination comes from 6 x SK6812 LEDs driven by a Wemo D1 mini, which is integrated with ESPhome and HomeAssistant (HASS) for seamless control. The image itself is printed in plain white PLA, as is the lid. In contrast, the base/back is...