wire cover for wall 3d models
2436272 3d models found related to wire cover for wall.thingiverse
Parametric cover for a holes you may drill for mains wires through table tops, cupboard walls and so on. The idea is that you may need a fairly big hole to enable the plug the go through. Which would leave a big, ugly and impractical hole, unless...
thingiverse
Wall mounting cover for two 20mm pipe. ...You can either print it as a single one or print it as split models and then super glue it.
prusaprinters
Wall mounting cover for two 20mm pipe. ...You can either print it as a single one or print it as split models and then super glue it.</p><h3>Print Settings</h3><p><strong>Printer Brand:</strong></p><p>Creality</p><p class="detail-setting...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1324924 Instructions Using the following options: wire_hole_offset = 20.0 hole_dia = 77 t_starts = 1 have_lower_frame = 0 tol = 0.7 wall = 1.2 hole_depth = 9 wire_dia = 8 lip = 3 t_pitch = 1.75...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1324924 Instructions Using the following options: wall = 1.2 have_lower_frame = 1 t_pitch = 1.75 hole_depth = 23 framewall = 4.0 t_starts = 6 lip = 5.0 wire_dia = 12.0 wire_hole_offset = 20.0...
thingiverse
Customized version of http://www.thingiverse.com/thing:1324924 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
Customized version of https://www.thingiverse.com/thing:1324924 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
Customized version of http://www.thingiverse.com/thing:1324924 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
Customized version of https://www.thingiverse.com/thing:1324924 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
Customized version of https://www.thingiverse.com/thing:1324924 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
Customized version of https://www.thingiverse.com/thing:1324924 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
built this cause there are non on here that meet what i needed. ...size every thin up 25mm for the best size. ... hope ya'll enjoy.
thingiverse
Here is a Wire cover intended to hide the wires of the Hephestos 2 extruder.
thingiverse
Little wall hook for small wire baskets with a wire diameter of under 3mm.
cults3d
Little wall hook for small wire baskets with a wire diameter of under 3mm.
thingiverse
Wire cover to tidy up the cables on top of the extruder. Can be printed in PLA, ABS or PETG. ...I printed it in PETG at 0.25mm.
thingiverse
And this one works works quite well :) Pull up the rod to release lock, turn handle to tighten wires, and push the rod back to lock. ...To ensure that the rod will not fall out you can use short copper wire, push it through small hole and twist...
prusaprinters
... PETG Notes: Print orientation is visible on the picture. Frame can be printed with basic 15% infill but with full supports, for the rod you should set 100% infill and no supports needed. Category: Outdoor & Garden
thingiverse
Print with many perimeters for maximum strength. Snap fit on 4.7mm diameter wire mesh. ... Onshape document:...
thingiverse
Very simple cover for covering the hole in the house wall where your wiring connects. Inner diameter 72 mm which should fit a 70 mm tube. ...Outsider diameter 100 mm.
thingiverse
This is a wire cover for an LED Cabinet Light from Ikea (DIODER - see link below). This covers the wire and gives a nice hidden finish for things like bookcases. You can chain multiple of these together to create a longer duct/cover or trim to...
prusaprinters
I like the quick disconnect add-on for the Original Prusa Enclosure, but didn't like the wires being bare (for aesthetic reasons). So I created this remix of the original Delta PSU wire cover that extends down over the back of the connector.
thingiverse
A simple thing, to organize the wires passing through these huge wholes on office desks. ...The idea was to keep the wires from falling into the whole when you are not using it and, cover the whole.
thingiverse
i made 2 for power and ground close to me then on the wall further up i made 5 for the different colors i seldom use. I will be making a bigger one for 18 gauge esc wire and 12 gauge power cable soon. I hope this comes in handy!! I also spool up...
thingiverse
Wire cover for running small cable or wire through a wall or cabinet. ...My intent is to use it on an RV to cover the outlet and seal with silicone on an antenna installation.
thingiverse
Co-worker has a vine on her desk that needs something to grab onto, so a remixed a wire management cover. Has a lip so the flat head bolts clear. This is a standard desk cover, so should fit most. ... I'll post the Fusion F3D file if it's wanted
thingiverse
Wall mount for 4mm wire mesh racks. ...Hole is 4.25mm to allow for printer or filament variations.