wltoys 12428 chassis 3d models
16884 3d models found related to wltoys 12428 chassis.thingiverse
MG 996R Holder (for WlToys 12428 chassis holes)
thingiverse
This is the set of chassis parts that goes with the solid front axle I made to convert the WLToys 12428 into a rock crawler. I modeled this stuff to work with cheap Chinese frame rails that are based on the Axial SCX10 II, so a lot of SCX10 parts...
thingiverse
-------- More stuff: Wltoys 12428 - 0081 Differential Then Cup https://www.thingiverse.com/thing:4042825 Wltoys 12428 - 0024 After the shaft sleeve https://www.thingiverse.com/thing:4042828 Wltoys 12428 - 0025 After the drive shaft...
thingiverse
This thing is a replacement spur for WLToys 12428, 62 teeth. I have seperated this thing in 2 parts in order to print it without support. If you want you can glue these two parts together. I am currently using it without glue. ...
cults3d
This thing is a replacement spur for WLToys 12428, 62 teeth. I have seperated this thing in 2 parts in order to print it without support. If you want you can glue these two parts together. ...I am currently using it without glue.
thingiverse
I had problem on my Wltoys 12428, that front differential was way too tight, it was almost not working. Car was understeering a lot. Therefore I did spacer to make it work better. In my case 0.3mm was the best, but you can download variable thickness...
thingiverse
Hi guys, If Thingiverse is as slow for you as it is for me, consider looking for your 3D parts at Cults 3D: https://cults3d.com/en/users/WrenchToDrive/creations WLToys 12428 rear suspension trailing arm and upper link. I printed these to test PETG...
thingiverse
Wltoys 12428 (Reely) Desert climber most likely to break part ready to be printed sidewise.
thingiverse
Bracket to mount DS3218MG 20kg servo in a WLToys 12428. Mount the servo to the bracket. Put the bracket in the chassis. It will only fit nicely one way. Once you are happy with the position, drill new holes in the chassis for the mounting screws....
cults3d
Bracket to mount DS3218MG 20kg servo in a WLToys 12428. Mount the servo to the bracket. Put the bracket in the chassis. It will only fit nicely one way. Once you are happy with the position, drill new holes in the chassis for the mounting screws.
thingiverse
Hi guys, If Thingiverse is as slow for you as it is for me, consider looking for your 3D parts at Cults 3D: https://cults3d.com/en/users/WrenchToDrive/creations Build Guide:...
thingiverse
Größerer Batterie halter für den Wltoys 12428 ! Zusätzlich mehr Federweg! Batterie Größe: ca. L>xBxH >107 or more x MAX: 34 x Max: 27mm Kann mit dem RF100 gedruckt werden! ...
thingiverse
Inside of the wheel from RC Car WLToys 12428. This wheel will propably fit in other tires than from that specific RC car. All dimensions are corect with original part, only difference that this wheel is fully closed from inside, and base offset of...
thingiverse
To do this modification, you will need a few things : 1°) Print the "WLtoys 12428 front shock tower" designed by tjheikki (https://www.thingiverse.com/thing:2864109) 2°) Put the electronic at the rear of the car, in the original battery tray 3°)...
thingiverse
My Wltoys 12427 (same 12428) suffered from noisy front differential (https://www.rcgroups.com/forums/showpost.php?p=43840841&postcount=3183) I designed a gasket for the front differential gearbox and 3D-printed it in PLA. It did reduce the noise...
thingiverse
WLToys 12428 ESC splash guard. Want to do some winter bashing? Want to keep that notoriously not water proof ESC alive? A splash guard couldn't hurt! Get that meltage down and away from the ESC. It's a little tall but I am able to button down...
thingiverse
WLToys 12428 motor splash guard. Want to do some winter bashing? Want to keep that notoriously flaky motor alive? A splash guard couldn't hurt! Keep that meltage off the motor. It's a little long and a tight fit but I am able to sneak it over...
thingiverse
Anybody using a WlToys 12428 (or similar, like Feiyue FE-03) will probably want better shock absorbers than the stock ones. The maximum length of about 95 mm for rear shocks limit quite a bit what can you use. 1:10 cars have a much better selection...
thingiverse
Hi guys, If Thingiverse is as slow for you as it is for me, consider looking for your 3D parts at Cults 3D: https://cults3d.com/en/users/WrenchToDrive/creations This is a Baja bumper and motor cage kit for the WLToys 12428 when running the SummitLink...
thingiverse
Trying to put your any good enough battery into 12428? no way... Welcome the battery tray widener :D With this you can load in your 3s-18650 easily and make it steady with velcro band holes are for zip ties to hang up some equip (like LV buzzer)...
thingiverse
Needed a mount to add some Taillights to my 12428. So i tried openSCAD and did this little thing. It's attached by 2 small screws. I drilled holes (1.2mm), so it fits very good. ... Printed with PET, it's flexible enough to not break.
thingiverse
lock designed to prevent patio umbrella from spinning around when tilted to block the sun. designed for a 37mm umbrella pole. May work for sizes ranging from 36-38, but not tested. If you found this useful, please donate what you think it is...
thingiverse
servo axis for steering WLTOYS 12428 - print with support
thingiverse
Battery bracket as spare part for WLtoys 12428 Desert Buggy